before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi,
The Bluetooth Channel Sounding specification empowers every compatible device (like the new nRF54L series devices) to be a mini radar actually. The Bluetooth Channel...
Hi,
Our team is considering the use of SiTime MEMS oscillators, namely a SiTime SiT1615B, to help in harsh shock and vibration conditions our product will be used in....
Hi, I am using the nRF52840 DK with SDK 17.0.2.
I am working on a project using the ESB protocol. In my design, an ACK packet is transmitted to the receiver every 5 seconds...
Hello community,
I was hoping to ask 2 questions about my design choices when designing around the nRF52840, specifically the QIAA-R branch.
First, I am confused on as...
Hi,
The Light Lightness Control (LC) Server controls a single Light Lightness Server instance on the same device with a state machine. Is there any application that demonstrate...
Hello,
I am using Bluetooth mesh for a project. I have a central device acting as a provisioner, and node devices that get provisioned as normal through this device. I am...
Hi,
My company has a product that is in production using the nRF5340 SOC. We noted this morning that the product would boot and application code even if the nRF5340's reset...
Hi there, I've a following set:
nPM1300-EK (PCA10152 / 1.3.0 / 2025.18 / Serial no. 10B3B784F5316C68)
nRF Connect v5.2.0
nPM PowerUP v2.2.3
After launching nPM...
Hello,
I’m evaluating whether simultaneous uplink from two ESB nodes is possible on the nRF54L15 DK. The documentation mentions support for up to 8 pipes in a star topology...
Hello,
I am using the ANNA-B112 module with nRF52832 to communicate to an AD5940 AFE using SPI1. I am also communicating with three other sensors using I2C0. This project...
Hi,
We enabled the DFU and sent a new application successfully using the mcumgr command line program, but now we need to do this upgrade process using the host MCU.
...
I am working through an evaluation stage for a new product using nRD52840, possibly updated to nRF54L in the next development phase. The device is based upon Zephyr and being...
I'm getting the warning about CONFIG_BT_CTLR, but I've gone through and changed to HAS_BT_CTLR. I do have the following:
# Maximum Transmission Unit config
CONFIG_BT_GATT_AUTO_UPDATE_MTU...
Hi
I have a nRF52840 setup with external 32 kHz xtal and external 32 MHz xtal, supplied by 3.3V.
I would like the system to be in as low power mode as possible.
Each...
