I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Good afternoon, I am new to nordic sensors. I would like to develop a phone application using Android studio that reads accelerometer values from the Nordic 52. How could...
Hello,
I am using nrf52840 with led blinky example for power consumption but it consumes 0 micro amp so i think reading was not correct so how can i troubleshoot this ....
I changed the SDK version of my project according to the steps of How can I change the SDK version of my program - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi...
Setup Visual Studio Code and installed the toolchain manager stuff got 1.9.1 of the SDK and the command line stuff for my windows 10 machine (if that matters). And trying...
Hello,
I have a Nordic Thingy 52, and I installed the Android application from github: https://github.com/NordicSemiconductor/Android-Nordic-Thingy
I can connect the...
Hello,
I am trying to send data via GATT notify at a rate of 60hz. I have created a tx thread that calls bt_gatt_notify in a loop and sleeps for 16ms. However, during profiling...
I asked this question in a different form but not getting any answers on that thread.
My goal is to publish battery level messages to a certain address and receive it on...
I would like to process and transfer decent quality audio (SBC A2DP) over bluetooth classic in addition to BLE sensor and display data transfer. Not looking for aptX level...
Hello Nordic,
I'm using the official DTM routine to do "SDPPI" certification for Indonesia, but I don't have any test process for Indonesian test engineers to use. Does...
Hi there, we have many nRF52840 devices in the field that currently run firmware based on the nRF5 SDK. We'd like to port our codebase to the nRF Connect SDK for all new products...
Hello,
I'm trying to publish values using a predefined message context.
This works fine when using bt_mesh_onoff_srv_pub or bt_mesh_lvl_srv_pub, but I get a crash...
Hej!
Do you have a reference design for nRF52840 and nRF21540, how to connect the ANT signal (nRF52840) to TRX (nRF21540)?
Is it enough to only use a DC block, C1=1.0pF...
Dear All
I used nRF24L01 antennas with external antenna for data reception and transmission at different speeds (256KBPS, 1MBPS and 2MBPS) for a while everything worked...
Hi
I'm having trouble when trying to connect nRF 52 DK with BLE app on nRF connect for desktop.
I can select device of my nRF52 DK, but cannot not scan any discovered...
