Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I have problem with wakeup of Low Power Node from System ON sleep mode. In debug session code works as expected, however outside the session something gets wrong.
The node...
Hi,
I'm trying to create an application based on the SMP Server app (NCS v1.7.0). I'm able to perform a FOTA using nRF Connect for Mobile and the app._update.bin without...
Hi,
I use the ble-app-uart-c-multilink example with a nRF52840 DK and 5 custom nRF52840 peripheral devices.
For a test, I want to connect to only one of those peripherals...
I am a newbie in nrF52832. I have been carrying some experiments using the Nrf51 and so far they are going so well. However, I came across some few E104-BT5052 samples originating...
In ncs1.7.1, I’m struggling with a problem about hard fault on nRF9160, but I have no idea to slove the problem.
nRF52840 transmits data to nRF9160 via UART0, the baudrate...
Hi,
I got the example http://github.com/NordicPlayground/nrf52-ble-multi-link-multi-role and the demo is OK.
I also use nRF Connect APP to connect the ble_aggregator,...
Hi,
Hope you are doing good.
I run the SAADC signal to from the sdk and observed that when the adc input is connected to ground, the adc reads few random negative value...
Using nRF9160, ncs 1.6 on a custom board and segger-SES for debugging, we have intermittent stops (debugger breaks) on an assembler line with 'cpsie' opcode:
File: cpu_idle...
Hello Nordic support,
I am using nRF5 SDK for a Zigbee coordinator application. In zboss_api.h, I see that there are functions for setting short pan id (zb_set_pan_id()...
Hi, I'm starting a new custom development, that will use NRF52805 SOC. The project will be one Alexa Gadget device. I have seen several documentations, but I have some question...
Hi,
I have met one bug.
when I flash a fw with generic level server , then flash other fw with sensor server , the system runs error, if I use command "nrfjprog --eraseall...
Hi Nordic,
I have written a device driver following the guide as Devicetree HOWTOs , and try to call the driver api in main(), but got unexpected output as below.
I...
Hi nrf masters!
We have a problem quite late in a large development project and urgently need assistants. We have spent hour's reading all posts about this and debugging...
Hi,
I would like to know if it is possible to implement with nRF9160 a communication to an ethernet port?
Also if the nRF9160 has CAN bus port.
Many thanks, Jose
