Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
Hello all,
I’ve already looked in the following files:
C:\ncs\v3 .1 .0 \zephyr\ include \zephyr\bluetooth\mesh\ access .h
C:\ncs\v3 .1 .0 \zephyr\ include \zephyr...
VS Code extension updated to 2025.8.654. Now when I click flash it says
And sits there spinning. Running west flash manually works.
Extension Features > Runtime status...
Hi all,
Im testing the "periodic_advertising_example" but in wireshark (nrf52840 dongle) I can just receive the AUX_ADV_IND packet below. I can I see the periodic advertising...
Application: Matter product using nRF54L15, SDK 3.0.0
Ecosystem: Matter product joins Apple HomePod
I am not able to get time/date delivered via Matter to the product...
What are the implications of doing this in one of the Kconfig files in one of my modules? should this override the first configuration of NFCT_IRQ_PRIORITY? from my undersanding...
I’m working on DFU using the BLE Mesh distributor and target sample codes. I built both with Sysbuild and flashed them onto two separate nRF52840 boards. The target board...
Hai,
We are developing a product having nrf54l05. I'm using nrf connect sdk for programming. I'm using one GPIOs for input. I have enabled pullup for that pin. We want to...
1. development environment:
software ncs3.0.1 , DW3xxx_XR6.0C_24Feb2022, vscode
hardware: nrf52840, DW3210
DW3210 is a UWB chip produced by Qorvo, and its corresponding...
Hello
I have just received thingy:91 x to start learning nrf platform. Unfortunately it's not all smooth. I am trying to do flash Blank application. It builds fine but then...
hi support team,
i have close this ticket:
but i need open this ticket and ask how to program 9151 externa; spi flash.
i don't know if 9151 json file is correct and...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Here’s what to check next for toolchain detection issues in VS Code with nRF Connect SDK:
1. nRF Connect Extension Output In VS Code, go to View → Output. Select nRF Connect...
Hi The Nordic Team,
I am developing a SED device of Matter over Thread. How can I get the ipv6 address of my parent node after my device is connected to the network?
...
