Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello, i'am trying to display data on my sensor Bme280 aka (temp, humidity and pression but the build is successful and the jlink is well connected the wiring is like below...
Hi,
I was using nRF Connect with all applications listed. But after installing nrfutil from git, the application all disappeared. I uninstalled nRF Connect and reinstall...
Hi, I'm attempting to use an nRF21540 to boost the range of a BLE Beacon, and I'm running into a lot of trouble getting the Eval/Dev Kit set up. First off, is there any documentation...
Is there an nRF Connect mesh sensor example. The light on/off example is great, but very simple. There is an nRF5-SDK-for-Mesh example. Are nRF5-SDK and nRF Connect compatible...
Hi to everyone,
I'm evaluating an application consisting of a bluetooth mesh where each node sends a status message to the others.
The area where the nodes will be deployed...
Hi,
We need to know the list of models (like health, configuration, lighting, sensor, generic on/off) in nCS sdk 1.7.0
can you please share inputs
thank you,
To update the Application, it is necessary to implement the update via CAN bus. Below is the hardware part, we use a CAN-SPI chip to access the bus.
We´ra using Microchip...
I would like to disable completely the 2.4Ghz radio after the 52840 has full soft device enabled and ble stack has been run.
This is after the full sequence of bluetooth...
Hi Devzone:
We put the radio test project on our custom battery powered board and encountered a problem.
When we disconnect the usb cable, the tone emitted by radio test...
Hello,
we developed the battery management system with a NRF52810.
Now the product is passing different certifications.
We need to provide info to the certification...
Hi
Trying to implement Full modem firmware update over serial port (USB) on nrf9160 in accordance with nrf\samples\nrf9160\fmfu_smp_svr in ncs version 1.5.1.
It seems...
Module: nRF52810
SDK: 14.2
Softdevice: S132 v5.1.0
Hi,
I modified the serial dfu bootloader exemple to use the SPI slave 0 instead of the UART to communicate between...
i try added Characteristic User Descriptor on nRF Connect BLE app
but on smartphone get Characteristic Extended Properties Descriptor
how can i fix this ?
Hi, I have some troubles with partitioning while using thingy91_nrf9160_ns. I have some FLASH overflow when compiling it with west using 1.7.0 library, while everything fits...
We have five nRF52840 DevKits (Mesh SDK 5.0.0) running to collect data. The devices don't have a stable power supply and regularly turn on and off. (We are only interested...
