I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Starting from NCS v3.2.0, up to the current NCS v3.2.2, I'm getting back -EIO when trying to use the I2C bus. In commit github.com/.../428ce9f27bc368f8023de98cdd494b060374962b...
Greetings,
We want to use the MCK of the I2S module as a clock output for an external device. For that, we need a freuqency of around 4,096MHz. ACLK originates from the...
HI
I am using the DTM example routine of NCS 3.2.1 and am currently testing the combination of nRF54L15 DK and nRF21540 EK. After flashing the original example routine to...
I’m using an nRF54L15 evaluation board obtained from a distributor and currently testing transmission and reception of large data chunks. I built a vender model and a custom...
General flow when the issue occurs:
1. buf is allocated on prep_pool in prep_write_cb: data -> buf = net_buf_alloc ( & prep_pool, K_NO_WAIT);
2. buf is put to prep_queue...
Hi everyone,
I am currently working on a project using the nRF54L05 and SE052F (from NXP).
I found this GitHub link: https://github.com/NXPPlugNTrust/nano-package/blob...
We are using an nRF52840 running SoftDevice Controller (SDC) in a custom Host + Controller architecture:
SDC runs on nRF52840 as the Bluetooth LE Controller.
Our...
Hi, I run Matter test TC_DefaultWarnings.py but failed the test, see below the last part of the logs:
******************************************************************...
Hello! I am trying to upload 120KB of data through 2 protocols: https and mqtt+tls. Both the cases have same configurations enabled in the context of wifi, net mgmt, network...
Hello, i'm trying to flash mfw-nr+_nrf91x1_2.0.0.zip on a thingy91 x. it doesnt work via nrfutil nrfutil device program --firmwaremfw-nr+_nrf91x1_2.0.0.zip THINGY91X_13A2EC8A4FC...
Hi, I'm having a pairing issue with nRF54L15 (Zephyr-based project) and I’m not sure if this is a security configuration problem or something related to bonding persistence...
The examples for the Matter Light Bulb app and others contain pm_static_...yml files with sections that look like:
I cannot find "orig_span" in the Partition Manager documentation...
I was asked by Nordic tech support to create a new ticket, because ticket number 357092 had become a long a winding thread.
I need a simple utility I can offer to an end...
I am developing a project using nRF5340 to drive some peripherals. During debugging, I found that no matter how I executed the pull-up/pull-down commands, the p1.00 and p1...
I am using qt C++ to refactor the dfu master station, currently I have a problem, that is, I want to communicate with 52840 simulated com but failed, I initialize, you see...
