I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello Nordic Forum,
I ran the Power Profiler Kit on an nRF52DK development board to establish a baseline power consumption.
The current firmware project is quite simple...
Hi,
I am developing a low power BLE device using Promicro nRF52840 boards. After updating to ncs3.2.1 I have noticed a high power consumption in sleep, that isn't present...
Hi! I'm running into a strange issue.
I have inherited this project and it is poorly commented. I have 2 peripherals and 1 central. The 2 peripherals are identical devices...
I am developing a product which uses one nRF5340 Timer in timer mode and another in Counter mode. Reading through the nRF5340 Product Specification v1.6 I have the following...
Hello Support Team,
I am currently working on Channel Sounding with the nRF54L15 devkit, and I am encountering an issue when using main_mode .
Until now, I was using the...
After defining the ADAPTER and initializing UART2 the The adapter pointer fails a test on line 287. FATAL: async_adapter_uart2 points to Flash (0x246d4). Linker Error. This...
Hi, I've tried signing up for a SUPL licence a couple of times but it keeps getting denied. Not sure why. I have logged into devzone.nordicsemi.com and am using the same email...
I’m trying to read/write data to the internal flash of my nRF54L15 SoC using the NVS (Non-Volatile Storage) library.
I successfully flashed the sample nvs application on...
I try to write data into the OTP section of the APP core with the following command line:
nrfjprog.exe -f nrf53 --program 'OTP.ihex'
ouput:
[error] [SeggerBackend] ...
I am trying to program MS12SF1 module through nrf5340DK. I tested the blinky code to toggle the LED pins but while checking through oscilloscope the pins showed nothing, wasn...
nRF54l10 on our custom board in system off has high current consumption, approx 98 uA.
Utilizing the system_off code (C:\ncs\v3.0.2\zephyr\samples\boards\nordic\system_off...
I have got to start with nRF7002-dk and the Wi-Fi sample from the quick start is not working.
I have tried to compile the code on VS code and flash the same code on the...
I would like to estimate the current consumption when the controller is advertising at 2.3Seconds, using external crystal, Tx power of 8dBm, Tx payload of 31 bytes. When I...
We are facing in BLE connection issue in Android phone.
we are planning to use 1. Android phone with 'nRF Connect' for mobile as BLE central. 2. Long range demo applictaion...
Hello.
I am currently testing nRF Cloud and encountering an issue.
I have flashed the Peripheral Memfault Diagnostic Service (MDS) sample program to an nRF54L15DK and...
