Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
We have code that puts the HW to sleep. On a nRF52833. The pseudo code would be something like this - <shutdown SD, stop freertos scheduler, stop interrupts, power down all...
my code base is samples/bluetooth/central_hids and samples/bluetooth/peripheral_hids_keyboard, NCS 2.6.1
Central
diff --git a/prj.conf b/prj.conf index c85e49d..0543efe...
Hi.
I try to build the nrf_audio sample as BIS headset with enabled FOTA and NCS2.7.0 and get the following link error for the ipc_radio image:
FAILED: zephyr/zephyr_pre0...
I need to use 9160 to drive the Lis2dw12 accelerometer for ST. I found some settings related to this accelerometer in NCS, but I couldn't use it after adding it in IIC, and...
Hello,
is there any technical reason why the MPSL radio notification API has been dropped somewhere before NCS 2.6?
Our application needs information about radio notifications...
Hi, I'm looking into a design based on the npm1300 and nrf5340 for a battery-powered wearable device.
We would like to use two buttons (A and B) as the user interface with...
We have nrf52840 S140 BLE Central device that currently connects to TI based sensors. I have implemented code that can upgrade those TI sensors' firmware using the TI BLE...
In BLE Fundamentals, Lesson 3, Ex. 1 (BLE connection exercise), the nRF84020 DK board indicates a successful connection (led 2 is on + connection message in serial terminal...
Currently, I am creating a CIS-connected device using nRF5340 Audio on a homemade board.
Since the circuit configurations of the Gateway and Headset are different, I have...
I just got a fresh Win install and installed a new version of vs code (details below) and lo and behold the nrf welcome page is empty! Apparently, this was changed a while...
Hi I am looking for some advice with regards to getting a Fanstel BU840XE ( BU840XE, The longest range, Remote USB Dongle for BLE 5, Thread, Zigbee — Fanstel ) device to function...
Hi team,
I am getting secure fault after PPP started in SLM (v2.6.1) application.
here is the snapshot of the error message
Anyone having same issue and resolved please...
I am experiencing an issue with the I2C device on the nRF5340(our custom board) where it is unable to read/write to the sensor, resulting in a return value of -5.(EIO)
Details...
Hi
I'm chnaging the Secure Bootloader to an external falsh for bank1, connected with QSPI.
In the function on_data_obj_write_request is the call for nrf_dfu_flash_store...
Hi,
I have a project with an nrf9160 running zephyr. Can codechecker be set up in the build in nrf connect in vs code so that when a build in vs code is done it runs code...
