before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hello Team, We are currently working on a new project that incorporates geofencing functionality using BLE. We have checked the current consumption in nRF52833 DK using the...
hi professor,
I'm using nrf5340 to design project,now I wan to reduce power consumption to uA level.According to https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog...
Hello, I am writing an AT command response parser for my custom AT commands. I thought about using nordic's parser utils found in include/modem/at_params.h but I have been...
Hi all !
I'm writing this message because I'm having problems trying to increase the number of devices in PAwR (I use Coded PHY).
I based my development on the SDK 2.8...
hello . i tested the sample for the persistance key it worked with the AES key . But when i tried with the EDDSA key i received that error psa_generate_key failed! (Error...
I have 7 GB large .ppk2 file exported by Power Profiler v4.2.1. I am looking for a glitch in power consumption. Doing this manually by scrolling through the waveform in Power...
HI! I am trying to decrease the memory use of my application that is built for a nrf9160 and noticed that tfm creates a 256kB partition that it only uses around 99kB of. RIght...
nRF54L15 has RRAM with error correction codes (ECC) built in, with autocorrection.
I guess ECC errors could either happen due to a power loss during a write (when reading...
i am working with the nrf7002+nrf5340 ns when i run the excercise solution and press the button a couple of times, i get this error *** Booting nRF Connect SDK v3.5.99-ncs1...
I am bringing up a brand new laptop for devlopment.
I downloaded and installesd nRF Connect, SDK 2.6.0, SDK 2.7.0 and SDK 2.8.0. The SDK 2.9.0 installation failed.
I...
I plan to use an ESB as a low latency and high speed protocol.
However, there must be multiple hosts on one network.
Hosts or devices must be able to communicate with...
Hi,
I have a design which mostly follows the reference designs.
I've added a Resistor Network R16/17/24 to allow a UFL connector to connect to the ANT and isolate...
Hello, I really need some help to connect a central nRF52 DK board to a peripheral that was provided to me. This peripheral can connect to a smartphone using nRF Connect and...
NCS 2.7 with Toolchain 2.7
Launch build from Visual Studio
Sysbuild with mcuboot and custom application, custom board
Although the application itself updates when VERSION...
In our custom board nrf5340-nrf7002, tried system_off(C:\ncs\v2.6.1\zephyr\samples\board\nrf )sample to check power consumption.
But it measures 0.60mA Is there any config...