I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
As per your sugesstion opened a new ticket in reference to existing ticket,
https://devzone.nordicsemi.com/f/nordic-q-a/60891/unable-to-read-the-128-bit-uuid-with...
Hi,
I'm using nrf52-pca10040 and sdk-15.3, I tested an eeprom chip following twi_scanner example, using no block nrf_drv_twi_xfer way, which works well, then I put it in...
Hello,
I followed this tutorial and github example in order to make a custom service with the characteristics I need. However, I am running into an issue where the board...
Hi.
I am using nRF52840 Dongle. A problem occurred while merging the PIN_CHANGE_INT examples based on the BLE_APP_BEACON example. I connected the external button to the...
In the products that I am developing we use advertising packets in the scan response to pass some data around our devices. We wanted a way for the app we've made for iOS to...
Hi,
I am using nRF52840, S140 7.0.1. I am using ble_app_blinky application.
I am writing data into FDS records. After writing FDS, if I load new hex file using nrfjprog...
Dear all,
I'm trying to go to SYSTEMOFF mode and then wake up from activity on UART rx pin (nrf51822).
If I do this:
nrf_uart_txrx_pins_set(NRF_UART0,NRF_UART_PSEL_DISCONNECTED...
Hello, I have a BLE peripheral, that should receive larger amounts of data using a l2cap channel. The central (a MacBook) creates the L2CAP channel, the channel is purely...
Hello,
we develop an open source framework that we are currently extending to also support the BLE Mesh Access Layer Models. We are currently implementing the foundation...
I am using nrf52810, using sdk15.2, softdevice6.1.0, my application flash takes up 56KB (I used fds), softdevice: 100KB and bootloader: 24KB, resulting in insufficient flash...
Hi,
I'm try to test my nRF52833DK using the nRF connect Direst Test Mode. Even if I flash the DTM binaries in nRF5 SDK 16, the Direct Test Mode app says something like ...
Dear Sir.
I am using SPI as follows.
gpio_pin_write(dev_io, LIS2DH12_CS_PIN, false); err = spi_transceive(spi_dev1, &spi_cfg1, &tx, &rx); gpio_pin_write(dev_io, LIS2DH12_CS_PIN...
The firmware is based on the BLE UART example running on an nRF52832 with the S132 softdevice. The first batch of boards were build with the QFABB0 chip revision of the nRF52832...
I have set up APP_BLE_CONN_CFG_TAG with
#define APP_BLE_CONN_CFG_TAG 1
Setting things up in ble_stack_init exacly the way it is done in the example, but when I run sd_ble_gap_connect...
Hi,
I am using nRF52840 S140 V7.0.1. I have few queries on GPIO configurations.
Below are my PULLUP/PULLDOWN macros.
As per my understanding
1) In below settings...
