Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
The Errata 155 workaround seems to work for the nRF52840, but only when events are configured before tasks. If I configure a task for an unused output pin *before* configuring...
Hello, I want to use the nRF52820 as a slave device. I've left my code, prj.conf, and DTS files below, but the spi_transceive function seems to be getting stuck. What could...
Hi,
I'm using the nRF52840 with the SoftDevice for BLE. In my system, it's primarily a BLE transceiver controlled via SPI by an external TI MSP430. We're considering implementing...
nRF54L15 LE Audio with I2S interface, LC3 codec point-to-point audio The specific flow is as follows: The nRF54L15 communicates with the mic via I2S to capture audio data...
I'm facing a persistent issue with my nRF9151-SMA-DK kit when trying to perform USB debugging, uploading, recovering, or erasing.
Interestingly, other boards (nRF9151-SMA...
Hello, we use nrf52832-ciaa in our project and it is light sensitive. Could we use x-ray to inspect soldering quality or it will damage the mcu? Thank you, Anton
I tried to find an explicit statement whether a new IMEI needs to be written to nRF9151.
These sources state that nRF91x1 ships without IMEI and it needs to be written:...
We are working with Nordic’s official peripheral_esl ( https://github.com/NordicPlayground/nrf-esl-bluetooth/tree/main/samples/peripheral_esl ) sample application for Electronic...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
I am getting the following build errors when working with both DFU (MCUboot) and the file system (FAT FS) together. Errors: D:/ncs/v2.9.0/zephyr/drivers/disk/flashdisk.c:533...
Hi,
We are working on a project using the nRF5340 Audio DK. We want to take user input either from UART or BLE, and switch between them based on the connection status. ...
I would like to know the approximate flash memory footprint required to implement BLE Mesh, Zigbee, and Thread , individually. Could you please provide the details for each...
Hello,
I've been trying to use the NRF Cloud A-GNSS capabilities using the location library. However, after carefully checking the documentation, I am still unable to do...
I have a thingy 91x and am trying to get the fuel gauge on the sample code working. It doesn't include the thingy91x as a sample of this, but is it still possible? As I know...
Hello forum ,
here i m using nrf52840 where it is customized board ....i tried to print jedec number for windbond w25q64 here this code prints the jedec number and also...
