I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Its clear there is little interest in this DK compared to the nRF52 version. I got instructions for that platform that actually worked.
Not so for the nRF51 DK. But I am...
I am using FreeRTOS and some of the commands there have two flavors: for using in regular code flow and when are executed from an ISR, but in nRF SDK components and examples...
Hi All,
I cannot get the NRF_LOG messages via RTT to the debug terminal in SES or RTT Viewer.
My setup: HW: PCA10040 SDK: 17.0.2 Project: nRF5_SDK_17.0.2_d674dde...
Hi,
I followed all the steps to get NCS up and running with SEGGER Embedded Studio. However, when I try to open an example, I get this error:
Including boilerplate ...
Hi all,
I am currently working with nRF52832 boards, and I am trying to save some values in my flash memory. I have already created a code for this purpose and I am able...
Hi, I'm currently trying to understand multi-Link and Immediate Alert Server Application (ias) examples in SDK 17.
While I'm analyzing them, I got some questions:
Q1)...
Hi,
I am working on the nRF52832 ,why i can't able to set the low 7.5 ms interval . I am getting the error at ble_advertising_start . Do I want to change anything else?...
We are preparing our nRF52 product for the unintentional radiator test. Currently, the SoftDevice is enabled and we have the low power mode disabled with the following changes...
Hi,
Looking for some guidance on how to use the 'cryptographically secure random number generator' in a Zephyr/nRF Connect SDK application on an 52840
Is this a supported...
Hi sometimes it happen with my nrf52832 based device. The common way I am programming firmware during development is next:
nrfjprog --program fw.hex --sectorerase --verify...
Hi,
I am working on the nRF52832 ,If i want my data to be transmit every 7.5ms then what should I set the minimum connection interval and maximum connection interval ? please...
Regarding that the nrf52811 is able to use direction finding, there is any example for configure a tag with the nrf52811 to be located? Did nordic finally release any AoA...
Hello,
Sorry if it will be long. thanks for the help.
Using nrf9160 dk. The first thing I want to ask is about is the pins. I want to make sure I am using the correct...
Hi
I am currently using nrf52840dk with zephyr, and SPI used to work fine.
Now, as a slave, the kit only reads the data read while MISO is high (this might be what's supposed...
Hi, I am trying to create and FOTA upgradable application on the nrf52811 SoC. I have managed to do the same for nrf52832, but when I repeated the process for nrf52811 it...
