Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hello,
I am developing using nrf51822 and J-Link.
In the Keil4 version, the RTT viewer worked fine, and only the project was migrated to the keil5 version,
but the RTT...
I'm using PCA10040 to test nRF52832.
But I can't see J-link device after connecting USB.
I installed J-link(segger), nRFgo studio, nrf command. But I can't see my PCA10040...
Hello, we are using the ble_app_uart example code, and are trying to modify it so that if a certain UART sequence is received from the connected microcontroller, it will disconnect...
Hi
I'm working on a project interfacing the nRF52840 board with the lis2dh12 accelerometer
I'm using SDK 15.3, basing my code on the provided driver and information...
Hello!
Now I have two devices about nrf52832 .One is central and another is peripheral. So I want to transfer the peripheral mac address to the central via nfc.
I do...
This is the config fun followed。
one sample every 125ns,one ant get 12us =96 samples.
and first 2+32 samples is ignored。
*******************************************...
I've already tried to set some zephyr configs, but n51822 to run as peripheral it nedds at least ~20KB
Have anyone got success or all the nrf51822 QFAA H2 will really never...
development environment： SDK 14.2 , NRF52840 as central and NRF52832 as periph for Bonding: Passkey Entry, Central displays, and the error occur on nrf52840.
I want to know...
Hi all! I am currently using an nrf52840, mesh sdk v3.20 and sdk v15.30
I have the following scenario which I am trying to solve:
I am receiving a new GAP name for each...
In an earlier thread ,
[quote userid="17188" url="~/f/nordic-q-a/33649/j-link-the-firmware-of-the-connected-j-link-does-not-support-the-following-memory-access-read-0x02000004...
I'm using the nus_c service with multiple central connections. Obviously, I need the connection handle in my event handler - ble_nus_c_evt_handler(ble_nus_c_t* p_ble_nus_c...
Our product use two NRF24L01+. One is for transmitting and another is for receiving. They communicate by 250Kbit/s. It is pre-production.
Now, we want use nrf52810 to instead...
I just trying log via Segger RTT viewer, followed the the same procedure as that of serial_lte_modem sample in my new project and could not see logs showing in the viewer...
I am working with nRF52 DK, SES4.30 and SDK 15.3 with SD 132.
This error just started occurring once I set up app_timers. My code for setting up my timers is below:
...
