I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
HW: 52840DK PCA10056 3.0.1 2023.16
NCS SDK: v2.8.0
I want to test Zephyr's BLE controller instead of the default SoftDevice controller, and the `prj.conf` of ISO_CENTRAL...
Hello.
I am trying to use nRF Connect SDK v2.8.0 and nRF52840 to run Matter's Light Switch and Light Bulb.
I was able to confirm that it works with nRF52840-DK, but...
Hi there,
Our firmware is built on NCS 2.6.1 (soon to be ported to 2.7.0) and uses MCUboot.
I want to set REGOUT0 to 5 (which corresponds to 3.3V) and the `nrfjprog -...
I am trying to upgrade my project which is previously build with NRF connect SDK 2.6.1 to 2.8.0
I am getting this error while building
warning: NCS_SAMPLE_MCUMGR_BT_OTA_DFU...
Greetings,
when trying to compile simple GPIO configuration for NRF5340, the compile fails with:
In file included from C:/Apps/NordicSemiconductor/SDKs/v2.7.0/zephyr/include...
Hi
I have set up VS Code (1.93.1) on my Mac (mac OS 14.6.1) with nRF packages and zephyr installed. My nRF5340 DK is also found (however, instead of a nice identificaiton...
I am reaching out to inquire about the support for the indication method in the Nordic nRF52840. Could you please confirm whether this method is supported in the Nordic SDK...
There was no problem when the current version of ccache was 4.6.1. However, the current version of ccache, 4.10.2, behaves differently with the --specs option. It will do...
Hello~
I am developing nrf52840 with zephyr ncs tool chain v2.7.0 and SDK v2.6.1.
What we need is to generate RSA key pairs and send public key to App to encrypt data...
Im trying to get SAADC to continuously sample using internal timer but im getting couple of samples and then it stops, tried everything but I'm obviously forgetting something...
Hello,
I am trying to use TIMER3 where it should count 1ms ticks for 15 seconds and then stop.
Tried the below code. However it never enters ISR.
Please let me know...
Hello,
I have a Insight ISP4520 SIp which include a nRF52832 chip and a SX1261 for Lora radio https://www.insightsip.com/products/combo-smart-modules/isp4520 The internal...
I'm using
the nRF52840 DK and the Matter light_bulb example, SDK v2.7.0.
a raspberry pi with the nRF dongle as a thread border router
the chip-tool running and compiled...
Al over these example programs there are all these messages like
LOG_INF ( "Filters matched. Address: %s connectable: %d " ,
addr , connectable );
How do you actually...
Hi,
We are using nrf52840 with nrfSDK-16.0. We have implemented extended advertisement in BLE 5 LE CODED PHY. We want to try periodic advertisements. Do we have any examples...
