Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
I want to use USB840F dongle connected to PC to scan for device and connect to other BLE devices.
Cannot find any documentation or example of how to do so using visual studio...
Hello, i have a nRF51422 DK and i want to revert back to J-link image but I cannot find the .bin either on the official site or on the internet ! I guess it's no longer available...
I need to transmit and receive data bytes over SPI module with nRF5340 DK board acting as the SPIM. Please help me with the DT configurations. I need to achieve the same using...
Good day,
I am trying to combine gzll, USBD HID and USBD CLI with SDK 17.1.0 and nrf 52840. GZLL receiving input, send to USBD HID, USBD CLI output logs and debugs.
Below...
Hi,
I am developing a nrf5340 based device (no external memory) using FOTA to update the firmware. This process used to work quite well for a while now, but I ran into trouble...
Hello,
I am trying to use PWM to control two LEDS, one red and one green (referred to as blueled in the code) to produce different colours. I have had a look at the example...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I'm studying the CDC_ACM...
Dear support team,
We need to add custom fields to the node database (CDB), as shown in the screenshot below:
Use bt_mesh_cdb_node_store(); to store, and then use the...
Hello,
I installed NRF Connect SDK 2.6.1 on Ubuntu following this guide, Now I try to follow the tutorial for Adding clusters to Matter applications . I'm stuck at (2) Adding...
In my last question, devzone.nordicsemi.com/.../can-cis-and-bis-modes-work-at-the-same-time-or-switching-freely , I have asked that if the CIS and BIS modes can work at the...
Hi.
I am using SDK v2.6.0 (Toolchain v.2.6.0). When I open VS Code (v1.91.1) I keep getting this warning -->Bad CMake executable: “”. Check to make sure it is installed...
Hello, I am developing on a custom board with the nrf5340 and programming through SWD using the nrf5340dk. A few days ago everything was running fine and I was able to continuously...
We're having an issue where our nrf52840 appears to stop advertising, and isn't able to resume advertising.
Our device is a custom PCB based on the Thingy91 (has both an...
Hi Nordic,
In my project, I have a NRF9160 and a NRF52832 with a ble host/controller stack over SPI HCI on NCS v2.5.2 As soon as I activate the HCI SPI in my project, the...
Hello Engineer Greeting of the day i am building my product using nrf52833 IC , there are some communication modules connected to the 52833 , i want to cheack lowest power...
