Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
I would like some help with porting the modem library (nrf_modem_lib) to work with my bare metal application. Besides a custom nrf_modem_os.c, I have made a slightly modified...
Hi!
Running LTE_BLE_GATEWAY example on nRF9160DK rev 1.1.3 gives "No HCI driver registered" error together with "Bluetooth init failed (err -19)". SDK/Toolset version is...
To preface:
nRF Connect SDK 2.9.0
nRF9151 DK
Windows 11 PC
Hello,
I have been developing in the nRF Connect SDK for a few weeks now so I am fairly new. I have...
When using the distance measurement sample code on my nrf5340 development kits, LEDs 1 and 2 seem to be working correctly, but LED 3 does not light up when connected. The...
Hi！
I'm working on direction finding. I'm using a nrf52833dk as a beacon, a nrf52833dk and a Direction Finding Antenna Board (PCA2005) as a locator for a bluetooth direction...
Hi All,
I recently received a few dev kit boards that I intended to use for a test fixture we are building. I tried to use it in our test fixture which had been working...
Hello, thingy53 qwicc connect shows 3.2V when pwrd on, yet there is 0v from thingy91x when turned on. Is there some other step needed to get 3.2V? thank-you,
Hello there,
Working on bringing up the FOTA feature on the 54L15. I began with the LBS example. I was using the Nordic "Device Manage" to push the FOTA build.
The state...
I've been using the following SPI2S pins and they've been working:
CLK -> P0.16 MOSI -> P0.17 MISO -> P0.19 CS -> P0.18
I want to use SPI1 instead but when I replace...
I have a two fold question, to build a prototype, I would like to know how to get
tflite micro in zephyr build for nRF9151 DK?
Non-Terrestrial Networks (NTN) on above...
I have been using the nRF Connect for Desktop with the Programmer application for several years to attach our end device to the Dev Kit to program our device with no issues...
Hi
Can the device(nrf52832) be used as a BLE Mesh Provisioner and Light Switch Client(such as Generic OnOff Client) at the same time?
I want to develop a device (nrf52832...
Thanks in advanced. Based on nRF5_SDK_17.0.2, I can use i2c with icm42670p normally. Due to power consideration, I need to r/w this imu with spi either to decide which is...
Hi,
I'm developing with nRF Connect SDK v2.9.0 in VS Code. I followed the exercise l1_e1 from the intermediate course. When I debug with breakpoints and the first breakpoint...
Hello there,
I reported this issue in another thread under a different symptom. With more and more testing, it shows it is somehow related to both Android and the 54L15...
