Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
To confirm, when connecting a power source to VBAT for the first time, nPM2100 will automatically transition to Active mode assuming the power source can deliver enough current...
The error started coming after updating the sdk version from ncs v.2.9 to ncs v3.1
[00:06:58.439,514] <inf> _https: Log:Sock before -1 [00:06:58.484,649] <inf>_https:...
Hello,
Going through DevAcademy SDK Intermediate and it mentions running 'west boards'. Doesn't work for me:
Any ideas ?
Sadly after weeks of little problems like this...
Below is my change, set options to BT_LE_PER_ADV_OPT_USE_TX_POWER
But it always display Failed to set periodic advertising parameters (err -5) , why?
My hardware is...
Hi again,
I'm having trouble with the Matter Test Harness. I have been running tests in isolation one by one and fixing issues the TH finds. Now I have run into an issue...
Hi,
toolchain:-v3.1.0,sdk:v3.1.0. i am using the vscode software for the development
Basically i am trying to connect the peripheral using the address (mac:- 7C:D9:F4...
Hello,
I am using NRF5340-DK for my project and I wanted to know if there is some example on how to read and extract the public key from this type of certificate. I have...
hi support team,
i am trying to help customer on demo about 9151 dfu 52840.
currently, 9151 is using nrf_cloud_rest_fota demo and 52840 is using "zephyr\samples\subsys...
I am able to successfully perform a firmware upgrade on the Distributor itself. However, when attempting to upgrade the Target devices, the mobile app shows Upload Complete...
Using the latest version of nRF Connect for VS Code, how can I display all output lines of the build process rather than the “condensed” line overwriting version. This used...
I'm seeing a few of these errors in my uart evt handler
I cannot seem to find where these are enumerated in app_uart_fifo.c or nnrf_drv_uart.h or nrfx_uarte.h.
Question...
Hi,
I have just received 2 DK boards for the nRF54L15 and using VScode to build and flash the code onto the DK
The reflector is detectable on my phone and I can connect...
SDK: nRF Connect SDK v2.9.0
Chipset: nRF52840
I'm using ncsv2.9.0nrfsamplesperipheralradio_test to test the RF.
The initialization code is as follows:
At this...
We have a custom board with npm1300 seem below. Im loosing 3mA more than expected. I used npm1300 both Vout1 and Vout2 before in other project. Same design and copmonents...
Dear Sir and Madam,
Now we are trying to certify Bluetooth qualification for our wireless module used nRF54L15, we are considering how we can set TSPX_FAE identifier?...
