Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hello,
I am looking to use the nRF9151 module.
I spoke with my wireless provider and asked what certifications they require to use their service. They said that they...
I am working on zigbee network
"In a Zigbee network, how can the coordinator retrieve the list of all devices connected to the network?"
What is the recommended way to...
Hello,
My team and I are working on a project where we need our nRF5340 to send data via UART from the board to a RaspberryPI. We designed a custom PCB with the chip and...
Hello,
We have devices in the field using NRF9160 V2 with NRF SDK 2.3.0 and MFW 1.3.4 on a Actinius Icarus V2 board. They are mostly working great, but sometimes some devices...
Hi, I am using nRF52840DK SDK 2.5.0 for testing Zigbee. I have three boards of this type, for the coordinator, router and end device.
For testing I use the end device I...
I am encountering the error <err> flash_nrf: invalid address: 0x00100ff8:8 when using NVS in my custom Zigbee project. However, the NVS functionality works properly in the...
I have a question regarding DFU while transitioning from development using the nRF52832 with the nRF5 SDK to the nRF5340 with NCS. Currently, I have a DFU app developed for...
I'm trying to install my dev environment on my MacBook. I've installed most of the tools but need the Segger installation to be properly licensed. I downloaded the Nordic...
Hello, After a lot of struggle i was finally made it to the point i can build and flash to my thingy 91 the lte_ble_gateway. However, i added prints (printk) in main.c to...
Im streaming audio from a gateway to headsets using BIS, but I am unable to get multiple streams working, so that I can switch between streams on the headsets. How do I set...
Dear,
We are using the nRF52840 with a proprietary protocol.
We plan to use the nRF52840 to sniff/poll RSSI on different (5/6) channels on periodic time (typ ~100 us)...
Hello, I have a problem on getting the dynamic tx power to work properly on the BL5340 using the hci_pwr_ctrl. I tried the example, it build and flash correctly, no error...
hi!
I get the message "The build configuration is stale. Run a pristine build" even after rebuilding in all versions of nrf connect for vs code after 2023.7.129.
I have...
I'm developing a product with the nRF52840, using Zephyr (Toolchain & SDK version 2.7.0). Is there a way to set up two PWM outputs having the same frequency and duty cycle...
Hi,
I am working on implementing an I2C node in my nRF52840 based sensor. However I am getting the following kernel panic.
I removed all I2C node related code that I...
