Hi
I try to run BLE HRS collector example.
when I run the project, in RTT terminal I have these error
00> sd_ble_enable: app_ram_base should be adjusted to 0x20001CD8...
Google open-sources the firmware needed to build hardware security keys
Google open-sourced today OpenSK, a Rust-based project to aid hardware vendors build hardware security...
I would like to store a simple integer value in the flash write and read after some event. I'm using the mesh example Dimming examples (experimental) in the nRF5 SDK for Mesh...
Hello,
Has there been any success with getting the python bindings for the pc-ble-driver running on openwrt? I've succeeded with the driver itself but not the bindings....
Hi Nordic Team,
In my BLE project I'm creating a Test application which gets all the advertising data from peripheral devices. The complete list of scanned device is received...
Hello all,
According to the documentation and this feedback on a case there is a maximum size for a particular cert before nrf_inbuilt_key_write returns NRF_ENOBUFS . Can...
Hello,
I am using nrf52840 DK, Segger Studio IDE, Win10.
My application is I want to transfer the image from iOS to the DK board.
I am aware of the Image Transfer...
Hi, all
I'm using nrf52832 pca10040, s132
I've asked several questions, but I haven't found a solution yet.
I want to send data through uart to the custom board.....
Hi,
I am trying to extract the static MAC address from a 52832 using NCS.
I do not want to try to read directly DEVICEADDR[0] or 1, but use a clean function.
I tried...
Hi People, I hope I can get help here or get pointed to a right forum where this can be answered.
I am using u-blox NINA-B306 (based on nRF52840) in one of my custom made...
Hello,
I am using the address resolution function getaddrinfo. Everythink looks fine, however I am wondering which DNS is used for that and if it is possible to update the...
Hi,
I am trying to do a quick PoC to connect some thread nodes to the cloud through a BorderRouter(RPi3b+ running Nordic Border Router, connected to a router using LAN...
I started with the peripherals/spi example, and am now trying to update to the recommended nfrx drivers. I can get the spi working fine, but I can not get the linking to work...
I am setting some manufacturer specific data to broadcast using sd_ble_gap_adv_data_set().
The data gets sent out perfectly when the advertising mode is BLE_GAP_ADV_TYPE_ADV_NONCONN_IND...
In my application, a host co-processor controls when to start/stop advertising, connect etc.
I've noticed that soft-device command are state-dependent, e.g. calling ble_advertising_start...
Hello, I discovered strange behaviour related to reset pin on my nrf52833 prototype and SDK17. My board has only reset button connected to reset input and 10K pull-up resistor...
Hello,
I'm having an issue with a hard fault when trying to write a specific value to a peripheral chip (TDC7201) register after multiple successful writes to the same register...
Hi all,
We're starting to move to the nrf52840 platform and have a question about the adc.. We'd like about ~13 bits of effective resolution- right now we use an ads1115...
Hi, I would like to try the Alexa_Gadget sample supplied in nRF Connect SDK v1.4.0 on an nRF52382DK but the sample does not build. I have tried both SES and command line builds...
We've been asked to run BLE transmissions using Ble_LR500Kbit, that is, Long range 500kbit/s TX. 125 kbit/s and 500 kbit/s RX on the nRF52840. The transmissions would be data...
Hello,
how much effort would it take to switch an application from the nRF52832 to the nRF52840 chip?
What we want to do is, we have a running application with the nRF52832...
To the kind attention of Nordic support team,
I'm interested in implementing some sort of validation stage using a keycode, as you mention in:
https://infocenter.nordicsemi...
