I was looking into the sdk provided by nordic for nrd52840Dk board and want to test the zigbee protocol. I havn't find any sdk for that.
Can you share me some links and...
Hello Team,
I want to configure P2.07 as UART RX for my custom board.
But when I clear the already assigned property as led2 for this pins from the pin editor gui, I am...
Hi,
I am trying to adding a coded phy support on my device in NCS project.
once I added CONFIG_BT_CTLR_PHY_CODED =y in my config , the ROM size will add more than 7kB...
board : nRF5340
sdk-nrf : v2.7.99-cs2
Zephyr version: 3.6.99
I am following https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/bootloaders_dfu/qspi_xip_split_image...
Hello Team,
We are working on custom board using nrf54l15 platform.
If we flash only application code, it works, LED is blinking & BLE advertises. But after adding DFU...
nRF52832, SDK17.1, s132 I work with SPI and it works on the this project with SDK15. But I have transferred this prj to the SDK17.1 and I can't make SPI work. I don't get...
We have a product which is based on nrf52840 and nrf connect sdk 2.8.0
After OTA sometimes, I find that the NVS is erased, which could lead to some issues on client side...
Hello, I am working on a project using zephyr as well as the nrf5340 MCU. For this test, I am on the nrf5340dk. My application requires I drive a PWM at 125khz. In my device...
I opened up the nRF Connect for Desktop application and noticed a new version for the SDK , 3.0.0. I also noticed that the application is being deprecated.
Inside of Visual...
I am trying to get my nRF9151DK connected to Azure IoT Hub. I have used the Azure IoT Hub sample, with some modifications to use LTE instead of WiFi which does not seem supported...
Hello, So I am working on implementing Bluetooth DFU OTA capabilities to send an image from a 54L15, acting as an SMP Central Client, to another 54L15, acting as an SMP Server...
I would like to use native CMake rather than West to take advantage of CMake Presets.
I have been able to make this work on the command line using the following command...
Hi , am developing the st7789v_minimal_sample application using Nrf52840. after creating minimal application am facing some unrecognisable issue. which am stuck can you please...
We have encountered a problem in using iic to communicate that the delay cannot be removed.
We are using the sample in NCS,
the address of the sample is C:\ncs\v2.6.1...
Hi,
I switched to SDK 3.0.0 and got back problem, that I had some time ago with 2.6?? When my code compiles, but controller stuck after many successful builds and I open...
C:\ncs\v2.6.2\nrf\samples\nrf5340\empty_app_core>west build –b nrf5340dk_nrf5340_cpuapp –p
while building the image, getting error:
ERROR: source directory –b does not...
Hi,
I got my hardware modification which added the nRF21540 to our system more or less running under NCS v2.9.0.
Currently, I have the following FEM and antenna configuration...
Hello,
We are using a BLE module based on nRF52832 with a U.FL connector for external antenna connection. One of our automated tests requires we turn off/on the antenna...
I just obtained a PPK2. Nice to see an ARM native installer for nRF Connect on MacOS.
However, for the PPK2, only "Not supported yet" is displayed.
MacOS version is 14...
Hello,
we implemented Zigbee coordinator. Few end devices left the network and we know that the issue is our side because the same devices work well with other coordinators...
