Hello,
I've been asked to create a new ticket for this. It follows on from
@ Erlend Isachsen asked:
So before marking this problem as resolved, it would be nice to be...
I am developing on the nrf9151 with SDK v3.4.0.
The device I am developing will be moving trough all of europe . My goal is to speed up the `AT+CFUN=1` conenction part of...
HI
I am currently carrying out secondary development for PAWR based on NCS 3.2.1. I understand that its communication adopts frequency hopping. I would like to ask whether...
NCS-3.4.0, on nRF5340, custom board losely based on PAN1783. No RTT backend, BLE stack works properly:
RTT enabled, BLE stack reads some garbage:
Printing is done...
Hello, our design does not use the USB block of the 52833. In the electrical schematic we have connected VBUS (AD2) to GND and we leave D-(AD4) and D+(AD6) open. Due to a...
SDK: nRF Connect SDK v3.4.0 (TF-M v2.3.0) Board: nRF9151 (seen on both nrf9151dk and a custom nRF9151 board) Config: CONFIG_TFM_PROFILE_TYPE_MINIMAL=y, MCUboot with CONFIG_USE_SEGGER_RTT...
Hi,
I have been tryring to identify the characteristic who is requesting a read. To do so, I implemented the read authorization request. Here is my code:
Basically...
Hello,
I'm trying to receive an inverted UART signal on the Arduino Nano 33 BLE (NRF52840). I've been able to invert the transmit signal okay using two GPIOTE channels and...
in ble send data period ,nrf 5340 CPU seem to be shared only by ble send
data ready and data read in ble not send period can equal ,this mean every data come from ecg chip...
Excuse me:
I'm testing the maximum rate of ble_app_uart。
1、Can the nrf connect app on IOS initiate the update of MTU and PHY?How to update MTU and PHY on IOS nrf connect...
I use nordic5340 SPI read ADS1298R ecg data, using nrf5340 p0.13 to connect ADS1298R data ready pin . when ADS1298R data ready pin high to low mean ADS1298R data ready .i...
Hi guys I am new to Nordic, just made a DevZone as the technology isvery interesting to me. So far I have been playing with ESP series but I know nordic is in a class of its...
Hello everyone,
I have been working for a few days with nRF52833DK building a BLE mesh where one of these microcontrollers is a client node or a server node.
However,...
Hi,
I have several questions about the dongle board.
1. Why should the p0.19,20,..,25 be connected to the reset pin?
2. what is the difference between the reset button...
Hi, All,
I saw the options for S2 and S8 in conn.h of ncs, but i don't know how to use it.
And I want to test the relevant data and differences between S=2 and S=8 broadcasting...
Hi Team
In nRF5340 Product Specification v1.1 page 117. The CACHEDATA is mapping as secure. But it have trust zone ID 252. So I have below questions
Does cache only...
This is a strange problem. 10% of our production boards fail outdoors within tens of seconds and will not fail after tens of minutes if indoors . The rest of our production...
Hello,
is there some existing example for nRF52840 DK, that would allow setting my own custom HID descriptor? e.g. "Telephony page (0x0B)" or a custom vendor-specific HID...
Hello,
I'm building a project for a nRF5340 and i need to use the mesh_stack.h library to reset device mesh configuration however every time i try to include it i get...
