Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
I have 2 hardware revisions, one with the GPS LNA attached to MAGPIO0, the other revision, the LNA is on COEX0.
In my prj.conf file, I have the following setup for handling...
From this guide:
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader#h61sjziauupw1j397q9s9ldr01q4j6d5
Appendix...
Hi,
I have the BC480 eval board and I would like to be able to upload the simplist application to it OTA. blinky_pca10056.hex
I'm using the Nordic Toolbox application...
'NRFX_SPIM0_INST_IDX' undeclared here (not in a function); did you mean 'NRFX_SPIM_INSTANCE'? error occured .
I am not using SPI , this error is not cured by me .I enable...
Hi
So I'm trying to adapt the ble_lte_gateway example at my nRF9160 DK but because I don't have a Thingy52 I have to use an nRF52840 device, so I wanted to try the sample...
I am working on a wearable design that has standalone modules distributed around the body. Each module will do the same thing, receiving commands to turn LEDs on/off or adjust...
Hi,
I am trying to us one more SWI with nrf_drv_swi_alloc , but returns NO_MEM => means there is not any free.
I looked to source code, and I find SD_SWI_USED is defined...
Hi,
I've added NUS service to my app (nRF52832, peripheral, FreeRTOS based, SDK 15.2, SD132). everything works great with MTU size = 23 bytes.
Now I try to increase...
Hi there,
I found very interesting behavior on casting double variables to integer.
The following code gives me strange result:
double dval = 0.;
int ival = (int...
Hey,
Currently I have been working on a project in which I have to calibrate the range of the bluetooth, basically I need very short range of about a meter.
Could anyone...
Hi,
I have some trouble using TWI : the slave device connected to nrf52 sends an ack signal (seen on scope) but the i2c handler raises an incorrect address error and discards...
Hi,
The device I am using is nRF52840, WLCSP package. Most of the analog IN pins are noted "low frequency I/O only", e.g. pins A5, A6, C7, C8. - I know there are some exceptions...
Hi,
As of now we are using SEGGER Embedded Studio for compilation and Flashing.
Now we would like to copile using Cmake tool, can you please provide template Cmake for...
