Hi
I try to run BLE HRS collector example.
when I run the project, in RTT terminal I have these error
00> sd_ble_enable: app_ram_base should be adjusted to 0x20001CD8...
Google open-sources the firmware needed to build hardware security keys
Google open-sourced today OpenSK, a Rust-based project to aid hardware vendors build hardware security...
I would like to store a simple integer value in the flash write and read after some event. I'm using the mesh example Dimming examples (experimental) in the nRF5 SDK for Mesh...
Hello,
Has there been any success with getting the python bindings for the pc-ble-driver running on openwrt? I've succeeded with the driver itself but not the bindings....
Hi Nordic Team,
In my BLE project I'm creating a Test application which gets all the advertising data from peripheral devices. The complete list of scanned device is received...
Hello all,
According to the documentation and this feedback on a case there is a maximum size for a particular cert before nrf_inbuilt_key_write returns NRF_ENOBUFS . Can...
Hello,
I am using nrf52840 DK, Segger Studio IDE, Win10.
My application is I want to transfer the image from iOS to the DK board.
I am aware of the Image Transfer...
Hello
I was working on a project, trying to enable the power management but I could not. So I just tested the simple zephyr sample application device_pm just to see if there...
Hello. We are testing the example of bl provisioning provided by sdk v2.8.0.
When the first wifi is connected, the wifi's data is stored on the board, and even if you turn...
Hello Nordic Team, I am working on a LE Audio project on NCS v2.9.0. My development board is nrf5340-dk. I am using unicast client example and I am trying to use it with my...
Hello,
In nRF Connect for Mobile, custom UUIDs show up as unknown, making it difficult to identify them easily.
Is there a way to add custom UUIDs, as can be done for...
Hello, I have recently switched to nrf52840 dongle for 802.15.4 sniffing.
I did a simple test with a ZigBee Green Power sensor sending data on channel 11. On the receiver...
Hi,
I am using a nrf52840 dongle for sniffing the bluetooth connection between 2 devices. These are the wireshark logs
What I could see is it initiates the pairing with...
I have a custom board with a nrf9160 on it that has been working for the last three months but last week when i was evaluating low power modes on the board i couldn't talk...
Hi,
i am using SDK version 2.1.1 and recently we had a problem due to the errata 160 which is fixed also in SDK 2.1.4
I am using Toolchain Manager 1.5.3 and i cannot select...
Hi,
we plan to use the nRF52832 in a new project, where we will need ANT support.
I've seen that it is possible to use the nRF5 SDK and the SoftDevice 332 to have ANT...
Hi everyone, I have a problems when I build custom board NRF54L15. I build this project for custom board for nrf52833. It's okay and no error. After that, I change this board...
Hi!
I am testing the nRF54L15-DK with 2.9.0 SDK and have some questions:
1. MX25R64: - why is it used in 1-bit (spi) and not 4-bit (qspi) mode? - OTOH this setup saves...
I have issue in newest SDK 2.8 of nRF Connect for VS Code. When I change something in prj.conf or in the source code, I often have to build and compile two or more times to...
I have looked at forum_post_1 , forum_link_2 and forum_link_3 . In short, I am following instructions for my_dongle . I have ncs 2.6.1. I have clones of nordics git repos...
