I thought this should be very simple but it has not turned out that way. I have started with the pc-ble-driver heart rate monitor (peripheral) example. I was able to take...
Hi,
I building a gas meter monitor ( peripheral ) that transmit meter reading to the Central.
The gas meter will be sending to the Central it's ID and meter value ( uint64_t...
The International Conference on Embedded Wireless Systems and Networks will host also this year a dependability competition to benchmark the performance of state-of-the-art...
Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
Hi there,
I have gotten to the very last step of the following tutorial: https://www.youtube.com/watch?v=kdMJQFDRoss
The issue I am facing is that when pairing the Matter...
Hello, I tried building the app showcased in this example: https://www.novelbits.io/smart-ble-lightbulb-application-nrf52/
I have gotten everything to build fine except...
Hello,
I need some help or advice on the easiest way to perform DFU in a nRF52832 device using a nRF52820 as a central through BLE. My nRF52832 device already has the DFU...
Hello, All
I am evaluating the example, following the instruction information here https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v17.1.0%2Fble_sdk_app_nus_eval...
Dear Support
Try to modify this use UART_1 for sending out data received via BLE, which is pin P0.14 on nrf52833dk_nrf52833, I modified Kconfig file under the boards folder...
Hello everyone, i am developing a board based on the nRF52832 microcontroller SDK v16.0.0 and sd132 for sending data of a sensor over BLE to a mobile APP. For this i am using...
Hi,
I'm implementing a hard real-time system (few us jitter) on nRF52840, SDK17.1, based on FreeRTOS project.
In the project, I need to sync GPIOs toggling with ADC...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
Is it possible to "WRITE" a characteristic that is larger than the MTU? As an example, we are considering the following...
Dear All,
I am looking for sample code to use an external QSPI flash (MACRONIX MX25R6435FZAIL0). The code is run an nRF52840 based custom board.
Your help is appreciated...
Hi,
I have a doubt regarding the possibility of removing or disabling an endpoint at runtime.
Assuming that we have a device with multiple endpoints, is there a mechanism...
Hi,
I have problem with program nrf21540 UICR mode. POUTA/B_UICR seem not set successful during measured here.
Below following which I write via SPI(Voltage is 3.5V)....
I am trying to use the nRF52840 Dongle as a controller with the Pi and ping devices (e.g. using l2ping to ping my phone)
I have flashed the bluetooth hci_usb sample on to...
Hello,
I am very new at this. I have just started to work with the nrf9160DK board, I am using modem firmware 1.3.1, and nRF Connect SDK 1.8.0. I am trying to test asset_tracker_v2...
Current result:nRF dongle is disconnecting with wireshark and Green led also stopped blinking
1. insert nRf dongle and open wireshark
2. Select nRf dongle(Green LED is...
I'm having an extremely annoying problem. I have an application that uses Nordic NUS service.
(1) I created it from the peripheral UART example for NRF52-DK, and adapted...
