The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
Hi,
I'm in the process of integrating nrf52840 module in HCI over UART to a linux host.
So far I have been able to build the hci_uart in from the samples and bring it...
Dear Members,
How can I share GPIO pin between SPI and I2C peripheral ?
I see SCK_PIN and MISO_PIN for SPI are the same with SCK and SDK on I2C
#define SER_APP_SPIM0_SCK_PIN...
For reference I am using the nRF5 SDK version 17.0.2. I have been comparing the flash_placement.xml files in the <SDK>/config directory and in some of the examples. I have...
Hi. I am looking for simple example of using QDEC for nrf5340. I want to use the Segger Embedded Studio.
Where can I find the example of some guide for HW driver for nrf5340pdk...
i am using nrf52833 development kit here i am using peripheral template as for coding purpose when i merge temperature sensor(SSTS751) code and W25Qxx code in it then the...
I am trying to build the connectivity hex files on an ubuntu build machine for an nrf52840 dongle so I can communicate with another nrf52840 dev board, I followed the instructions...
Hello, my project has 3 different devices (2 sensor and flash memory) on the same SPI bus all with their own CS. I ran across the following question , which has a response...
Hi ,
My environment :
nrf connect sdk
nrf5340 dk
segger studio IDE
verified method 1:
As per nrf5340 product specification document , we can protect the...
Hello,
I was recently trying out some samples with the nRF9160 DK and I had run into some issues when trying to run the nRF Cloud Client Application .
I had flashed...
Hi,
I'm developing on the nRF52 DK which has the nRF52832 chip.
I have a small vibration motor which I'd like to control on/off through one of the boards GPIO pins. At...
Hi,
I'm trying to modify the light bulb example and turn it into a light switch (not a light switch that controls another bulb in the network), but I'm quite new on the...
Hi,
I've noticed that there was an issue with ble_nus in SDK 15.3 - detailed in this post .
I'm using SDK 17, and in my application, I don't check data_handler != NULL...
Hi. I am using nrf52840 with Softdevice 16.0.0.
I set the maximum size to 247 bytes. But I probably only need 68 bytes per packet.
Should I reduce my MTU size to 71 or...
