Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
I am using SDK 11.0.0 and S132 on a nRF52832. In my application, my device can operate in BLE mode with the SoftDevice enabled or in custom RF mode with the SoftDevice disabled...
I need an accurate timer to generate pulses about 20ms. With simple timer this is workiong fine, but I need more then one timer simultaneously. So I would like to use app_timer...
Hi
I am working on NRF51822. I am using S120 ble_app_multilink_central example. I am trying to create a Timer1 interrupt of 1ms interval. My interrupt is working but interval...
Hi all,
I am trying to block connection from other devices to my nrf51dk board, except some specific devices. I used whitelist but it seem like the peripheral only block...
Hi,
I have just bought a nRF51822 Beacon Kit. The sticker on it shows that it is a PCA10006, Rev 1.2.0 2015.17 on it.
But I think that it is PCA20006.
What is the best...
Hi
I am getting some weird response from my nRF51-DK.
Situation 1:
When I try to flash it with the Blinky code (\sdk11\examples\peripheral\blinky\pca10028\s130\arm5_no_packs...
I'm trying to under the ble_app_multirole_lesc project and I'm a bit confused about calling sd_ble_auth_key_reply and sd_ble_lesc_dhkey_reply. If you are using Just Works...
Hi,
I am trying to send a HEX command to a device over UART at 9600bps using nRF52 DK, but it never works. However, it works with Arduino (so the receiving device should...
I have nRF52 Development Kit,after my first time programming the Firmware to my board.I can't erase or program it any more?
The nRF52 Development Kit can be connected with...
Hi,
I have read the following posts and understand how low clock frequency mode can be selected
devzone.nordicsemi.com/.../
I've also read in many posts that 4s calibration...
Dear Sir:
Could I use the external reference AREF1(pin0.06) instead of internal VBG 1.2V for ADC operation ?
I do the following settings to config using external reference...
Hi, I am using HRM example from SDK 10.0 with s130 on nrf51822 (attached project herewith). When I try to bond from Android(master control panel of Nordic), I am able to get...
100835_Rev1.PDF SRU532.pdf n5_starterkit.h
main.c
Hi,
i am currently working on the Nrf51422 chip with s310 softdevice . The problem i am facing is that when i dump...
Hi!
I'm fiddling around with the PCA10040 and the experimental_ble_app_blinky from the SDK found in examples/ble_peripheral/experimental_ble_app_blinky. I've had great...
