I thought this should be very simple but it has not turned out that way. I have started with the pc-ble-driver heart rate monitor (peripheral) example. I was able to take...
Hi,
I building a gas meter monitor ( peripheral ) that transmit meter reading to the Central.
The gas meter will be sending to the Central it's ID and meter value ( uint64_t...
The International Conference on Embedded Wireless Systems and Networks will host also this year a dependability competition to benchmark the performance of state-of-the-art...
Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
Hi,
we have ESB PTX and PRX couple from nRF54H20
nRF54H20DK (rev. 0.9.1), SDK: v2.9.0-nRF54H20-rc2 and the same Toolchain, IDE: VSCode + nRF Connect plugin
build for...
Hi,nordic team，
I'm developing a keyboard with the nRF52840 and NCS desktop, and it has a dongle. I hope Nordic's LLPM can reduce latency. But I can't find in the docs how...
If I have an application where I have implemented USB CDC-ACM, how can I set the serial number seen by the PC when I connect my device? Is it possible to set it at runtime...
Hi,
I am implementing discovery service but getting undefined error with below
bt_dis_pnp_params pnp_id = {
.vendor_id_source = BT_DIS_VENDOR_ID_SRC_USB,
.vendor_id...
Hi!
I’m developing an application using nRF SDK 2.9.0 with the Xiao BLE Sense . I created a new project based on Zephyr’s UART peripheral example.
The application runs...
I’m trying to implement DFU upgrade of NRF5340, I can send the image (./build_5340_app/build/signed_by_mcuboot_and_b0_s1_image.bin) to the device when running and it seems...
According to the documentation, you should run azure_iot_hub_dps_reset() in order to force DPS registration again.
But if the device has previously been enrolled and a device...
1. What is the Bluetooth version in NCS 2.6.1?
2. How to get Bluetooth version from NCS? is there any variable? I cannot find it in the release note neither. https://docs...
Hello,
I am using nRF Connect SDK v2.9.0, and nRF54l15 board. I enabled the watchdog timer and used its driver in zephyr/drivers/watchdog.h
It seems to work fine. The...
I have checked the PWM library in the nRF Connect SDK, and it seems that the library does not support init and deinit functions. The function pwm_set_pulse_dt(&pwm_led, 0...
Hello,
I’m currently working with a custom board based on the nRF9160 SiP, and I would like to measure the LTE-M TX power after the antenna impedance matching circuit. Ideally...
I am using the nrf52840 chip on a custom made PCB that is powered by a USB-C which provides it with 5V.This 5V is then converted to 12V using CH224K which then is wired to...
Hi,
we have ESB PTX and PRX couple from nRF54H20 nRF54H20DK (rev. 0.9.1), SDK: v2.9.0-nRF54H20-rc2 and the same Toolchain, IDE: VSCode + nRF Connect plugin build for CPURAD...
Using wireless sensors with nRF54L15, the sensors do not need to be connected, only broadcast a small amount of information. There will be 50-60 thousand nodes, and they are...
