hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”,I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hello!
Our current project is bare metal and has logging over CLI. I'm in the process of setting up a new project of ours that uses FreeRTOS but reuses a lot of the same...
Hi! We have a custom board and when ordering a new version we now get Errors on two of the 18 prototypes.
After trying on another machine with another JLink one of the two...
Hey, I have been trying to get to the root of additional current draw when crypto drivers are enabled.
Without the crypto drivers enabled the current draw between two advertisements...
Hi,
We are working on our manufacturing process that involves use of the nRF9160. I need a way to programmatically get the IMEI and ICCID in order to register the device...
I'm running a nRF52 device that's built on nRF5 SDK11, and it's remaining that way now due to regulatory reasons. My application needed to be updated to support bonding, and...
I have a nRF9160DK board running asset_tracker_v2 on a nRF9160 custom board. V1.7.0 loads and boots fine but when I use V2.5.0 the boot fails as shown below. The only change...
Hello, per the product specification, I see that the nRF52832 CIAA variant requires a shunt 1.0pF capacitor and series 3.3nH inductor.
Is this recommended regardless of...
Hello,
first I would like to "set the scene".
* hardware : cutsom board
* mcu : nrf52832
* nRF5_SDK : nRF5_SDK_17.0.2_d674dde
* software : mbr + bootloader + softdevice...
I have configured NRF52840 as coordinator ,EFR1 (ENDDEVICE) and EFR2(ENDDEVICE) as end devices. These 3 devices are connected in network.EFR2(End device )continuously sending...
I would like to understand the issue of frequency offset calibration in RF signals, I have viewed the
Case ID: 309794
nwp_006.pdf
I would like to know if I can do...
Hi,
We are working on BLE MESH using nRF52840. We are trying to put nRF52840 into deep sleep mode. The deep sleep current is about 210 micro Amp. Further, the current is...
Hi,
I have a coap server/client system and when I send a provisioning request from the client I can see the server is sending the reply. But my 'on_provisioning_reply (...
Hi,
I'm using SPI4M on nRF53 and came across it's errata, but I didn't get where to call the workaround functions.
The workaround is to call the below line upon enabling...
Hi I have a mbed application, which runs on a PSOC6 MCU, i am going to be using a fanstel BC832 (which is based of NRF52832)BT module for RF-communication. To verify that...
I have a custom board with an nRF5340 on it. I'd like to offload BLE operations to the network core using the RPC library to control it from the application core.
The documentation...
Quick Background
The spi_transceive_cb() function in Zephyr takes two buffer sets (among other arguments). One buffer set to TX and one buffer set to RX. You may pass NULL...