It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi All,
Hardware : nrf52840 early DK (PCA10056)
I modified Zephyr code from " central_multilink " sample to connect to 15 HR devices. The connection to all 15 devices...
The datasheet for the nrf52832 specifies two key constraints:
I/O pin voltage max VDD + 0.3V, min -0.3V
The AIN0-AIN7 inputs cannot exceed VDD, or be lower than VSS...
We use the pc-ble-driver with the nRF52840-Dongle and we experience intermittent issues where communication with the dongle will just stop and result in a NRF_ERROR_SD_RPC_NO_RESPONSE...
Hello,
I am having an issue with trying to install the nrfutil program from this Nordic download page . When I click on the download for the Linux(x64) version of the nrfutil...
I'm not totally clear from the SDK documentation on when I can expect NRF_ERROR_BUSY from sd_ble_gap_data_length_update(). Would it happen in the case where both sides attempted...
Hello,
My peripheral device is nRF52840, central is an Android device, Sniffer hardware is PCA10040 kit.
Using this guide https://infocenter.nordicsemi.com/pdf/nRF_Sniffer_BLE_UG_v3...
We have an application that needs to read device battery voltage and a sensor value every 10 seconds. The ADC is using burst mode and 8X oversampling to take each sample....
I created a new dts folder for nrf5340 appcore. The application works fine on the project, but I find netcore is not working properly. I found that the BOARD_ENABLE_CPUNET...
Hello,
My device is already implementing DFU over BLE and all is working fine. But now, I want to add the update over LTEM (Quectel BG77).
I want to proceed like this...
Basic OpenThread application built for 5340 crashes in net app.
The same application works fine on 21540 (52840 + 21540)
The crash seems to happen when some thread packet...
Hello,
I have 2x PCA10040 dev kits connected via SPI.
Device #1 is talking to a custom board MCU by UART
Device #2 is connected by BT to my android app
The task is...
Hello,
I am planning to use the balun BD2425P50100AHF with the nRF52833. The voltage on the pins BAL1 and BAL2 can go up to 15V.
I am wondering what is the maximum allowed...
Hi,
We have developed an application in central mode using BLE nRF52833 chip running on SoftDevice140 , Version 7.2.0
We now need to add support for FEM nRF21540 ...
Hi,
I am using NRF52840 development kit and I need to modify the PCNF0 register values for our application.
I am developing our application using the sample application...
I have ran the Mesh light demo successfully, and capture the Bluetooth HCI log (*cfa file) from my Android phone.
However，the transaction between my phone and the nRF52840...
