Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
I was using sdk 1.9.1 into my project and every things waking prefect which use openthread. I took the same project and build it in latest version ( sdk v2.1.1 ). when I flash...
We have created a zigbee custom sleepy end device with the base from light switch example. We are able to perform most of the operations successfully.
We have set the following...
in main.c, you have this code
but if you set CONFIG_BT_NUS_SECURITY_ENABLED=n in the prj.conf file, then there are #defines that will prevent the definition of the...
There are two DKs, one works as a slave while the other works as a master. When these two peripherals are connected via Bluetooth, they exchange each other's parameters via...
Dear Support Team
Our customer prepared to develop a triple mode operation game keyboard which communicating over Bluetooth LE, either via the dongle or USB. Should the...
Hello, thank you for taking the time to read this.
I've been reading through some of the forms, and I'd highly appreciate someone with more experience giving me some input...
Hi Support Team,
I’m designing a custom PCB using the nRF52840 based on "Circuit configuration no. 6" from the nRF52840_PS_v1.0.pdf. On our design, VDD_nRF = 1.8V which...
Hello,
I'm making some sensors based on nRF52832 and I'm using them as native transceivers. Maybe I'll look at BLE Mesh in the future but at the moment I just send and receive...
SDK 17.1.0
I developed a firmware that can be used in nrf52833-CJAA-R, but it can't be used in the nrf52833-CJAA-B.
According to the following link:
devzone.nordicsemi...
Hi Nordicsemi Team,
The one of our customers recently purchased NRF52-DK (Dev. Kit) which was Ver 2.1.0.
But This time has issue. He thinks after version 3.0.0. cause...
Hi, I am currently trying to use PWM on nrf9160 DK to control a stepper motor. Do you have any sample code for PWM? Also do you have the pin assignment of which pin on the...
Hello! I am working on a project I have set " sensor/server" as my starting point. The sensor is successfully interfaced with NRF52 I need to store the calibrated data of...
We're trying to develop a device driver by putting it in our application folder (under /drivers).
The west build system now recognises and builds it through the Kconfig...
I am following the instructions to set up NUS shell through bluetooth with the following example: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth...
hello
I try to make work the ADC on the NRF52840DK
I would like to use any of the 6 channels on the ARDUINO connector (p0.3, p0.4, p0.28-p0.31)
I am simply not able...
