I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
For power optimization I did to disable Mesh Using this piece of Code
and Re- Enable using this code
So the Real Question is that , After disabling Mesh for some time...
Hi
I need a suggestion. We are like to try a long-distance I2C communication between the sensor & Nrf5340 that is we need to connect 1.5 meters of cable between them. So...
The device advertises.
The phone scans.
The device use white listing and only allow one peer, the phone.
What's the difference between erasing bonds and disabling white...
Hi there,
I'm intending to use the nrfxlib modem library and its BSD socket implementation on the nRF9160. My goal is to use non-blocking APIs and use `nrf_poll` in response...
Hi,
I followed the DFU to SDK example post on https://www.u-blox.com/en/docs/UBX-19050198 to add Buttonless DFU to an application (I modified \ble_peripheral\ble_app_hrs...
Hi,
I'm using nRF Connect SDK v1.7.0 to develop a firmware for a custom board with a nRF52832 MCU. I'm using VSCode to build and flash my device using the nRF Extension...
Hi All,
My dev environment is as follow:
nRF52832(Central) + S132 + SES + SDK 17.0.2
Normally my Multilink Central code is flashing and working properly without...
I'd like to know of an example(s) for interfacing nRF52840DK board as a Master SPI to an Arduino badge (from Honeywell). I have the badge working with an Arduino Uno (Rev...
Hi,
If I want to use the NRF52833 as TX, and NRF24LE1 as receiver. How I can I match out the address?
If NRf24le1,
RX_addr = {0x00, 0x 11, 0x 22, 0x 33, 0x 44}
then...
Hello,
I'm working with NCS 1.7.1 and the nrf52840 dev kit to implement a BLE peripheral with FOTA, stats and configuration features. I've added MCUMGR to the project so...
Hi Sir,
As we know the inductor connected to the DCCH pin is a DCDC function for high voltage mode.
But what side effect we can see if we connected the inductor at the...
Hi,
I'm using NRF52840 to connect to an Android mobile phone.
The application scans for advertisement and when the NRF device starts advertising - connection is established...
Hi,
I'm evaluating the performance of the Zigbee protocol implementation on the nRF connect SDK using nRF52840dk:s. nRF connect SDK 1.7.0, ZBOSS I'm not sure where to find...
Hi everyone,
We are using the secure bootloader in our board, and we are adapting that bootloader for our requirements. Moreover, we use the DFU updates for our Main application...
