Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
Hello
Is there any example code in the Zephyr for operating as the Mesh provisioner/controller using the serial mesh interface on the nRF52840.
I am working on using the...
I'm having a peculiar problem with my device in a memory heavy application, two of my libraries use statically allocated memory and one uses what i allocate with mem_manager...
Hello.
I'm working for a Zigbee networking project.I chose nRF52840 as the coordinator.The coordinator acts as a gateway to communicate with Zigbee 3.0 devices on the market...
Hi. I am trying to add FDS to my application where I used freertos and ble. I tried few things always ending with hardfault, one time it was from Freertos scheduler and the...
Hi
I have a problem changing the max_rx_octets and max_tx_octets parameters with the sd_ble_gap_data_length_update function. On request from the app the size is attempted...
HI, we have updated our DK firmware (mfwnb1nrf9160030123prealpha) for nb-iot but after inserting the Vodafone (Ireland) V-Sim we only have a flashing LED 3.
nRF connect...
Hi all
Chapter 26.1.1 of the nRF51 series reference manual v3.0 states that the pins used by the SPI master have to be configured in the GPIO registers according to table...
Hi, I am interested to learn THINGY 52 working
I want to know how does the Thingy52 works?. any tutorial to explain the function of THINGY52
How to delete the boot loader...
Hi
The example in SDK15.2 for 52840 as a Beacon is not long range (I think).
Is there another example that will enable long range and also to enable connection?
While...
Hello,
I'm use laird BL651 with nRF52810 module. I flash the chip with beacon program from zephyr samples. I use Segger Studio.
The chip is discovered by smartphone (with...
Hi,
is it possible to scan 10000 beacon having adv interval of 10 seconds. is their any maths or formul we can do ?
i have set nrf52 to scan continuesly,
Hi,
There have 4 PWM sample code (low_power_pwm, pwm_driver, pwm_library and pwr_mgmt) in SDK 15.2.
I my use case is "Control 6 PWM output with different duty-cycle and...
We have written an application based on SDK V12.2.0 using S132_V3.1.0 for the nRF52832 and have been dealing with an issue where the module constantly enters a hardfault....
Let's suppose the PC (a laptop) goes to standby while a BLE connection is established with a Nordic dongle using pc-ble-driver v4.0.0:
- With SD API V2, status handler is...
Hi
I downloaded and successfully build and ran the asset tracker sample on the nRF9160 DK using segger embedded studio. In a first step I want to reroute the debug UART...
