Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I was trying to setup a nordic nRF9160DK following the steps present on the first lesson of the course "Cellular IoT Fundamentals", and fail to do so. When I got to the verification...
Hi,
I have used PPK2 to measure nRF9160 current using different boards. I like the product, but I'd like to note is that there seems to be a typo in the PPK2 documentation...
Hello,
When we try to run the standard radio tests for bluetooth, we get really low power compared to what is expected (difference of about 32db). Turns out SW_CTRL0 was...
Hi there, I am working on SMP client server application where I want to do the DFU of server from the client side where both the server and client are nrf52840 dev boards...
Hi,
I followed the instructions listed in Installing the nRF Connect SDK (nordicsemi.com) . Then I followed the steps in How to create and build an application (nordicsemi...
I am working on nrf52832 development kit for interfacing SX1262 Lora module via SPI. I have configured SPI 0 as follows:
Initially I am trying to read the SX1262_REG_SYNC_WORD...
Device/Board: nRF5340 DK Application: Mesh Light (Bluetooth Mesh Network)
Use Case: I am currently working on a Bluetooth Mesh network using the nRF5340 DK. My goal is to...
Hi,
We are using nRF SDK 2.6.1 and have selected the nrf7002dk_nrf5340_cpuapp target. After adding CONFIG_BOOTLOADER_MCUBOOT=y to the soc_flash_nrf example,
the code fails...
Hi everyone,
I have a problem about MBR and Bootloader memory (at address 0x74000). I am using nRF52832 S132 v6.
My purpose is that I can upgrade bootloader from inside...
I am designing an FPGA to have a SPI slave port connected to the nRF5340 SPIM4 master running at 32 MHz. But the setup and hold times for this configuration are missing from...
I would like to wake my app from sleep (k_msleep) on a GPIO interrupt. I'm finding that enabling the interrupt draws an additional 6uA however (8uA vs 2uA without it) - am...
I would like to set a gpio pin on Radio RX Ready and clear it on Radio Disable all via PPI. Below is my code. I only get the pin to change levels when the OUT task polarity...
We are looking into the following link for the softdevice S112 API documentation however we are getting Error Code 404.
Technical Documentation (nordicsemi.com)
Can...
Hi ,
I want to enable encryption in Bluetooth communication for a proof of concept.
I have Wi-Fi Provisioning example and in that while sending the wi-fi password ,...
Hello,
We are using nPM1300 in our project.
I would like to configure it to the maximum possible discharge current limit, as there are inrush currents in the board.
...
