Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
Content: I’m working on integrating the nRF7002 EK over SPI with an nRF54L15 using nRF Connect SDK v3.1.1 . While setting up the workspace, I noticed that the Wi-Fi driver...
I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
I used the nRF Audio Example to build a BLE audio device. I use the test tone generator functionality. I was previously using nRF Connect SDK 2.6.1 and the test tone generation...
I am an FAE with Ezurio, we have a customer who was running through the nRF Connect SDK Intermediate training on DevAcademy and they ran into issues with AuTerm in Lesson...
## Description
On the nRF54L15DK, the measured floor current increases significantly when the GPIO is configured for button edge detection.
### Observed Behavior
* Floor...
Hi,
I am quite new to nrf's and zephyr and I'm working on a product that requires Direct Test Mode functionality. I started with the DTM sample and am now looking at how...
Why do I often fail to compile the examples due to west? The prompt suggests that I need to upgrade west, but I am unable to do so?When directly upgrading West through VSCode...
The solution for "nRF Connect SDK Intermediate - Lesson 9 Exercise 5" does not appear to boot-up after flashing and gives the following output on the com port:
*** Booting...
Currently with the DECT NR+ modem API on nRF91x1 I can schedule rx operations in mode NRF_MODEM_DECT_PHY_RX_MODE_CONTINUOUS given to nrf_modem_dect_phy_rx via nrf_modem_dect_phy_rx_params...
Is there a way to create custom battery profiles of non rechargeable batteries for the nPM 2100 PMIC? Is the nPM Fuel Gauge board compatible with the nPM 2100 EK?
Hello,
I am using nRF5340 with nrf v2.7.99-cs2.
We have interfaced External flash MX25R over nRF5340's QSPI channel. We are using XiP as well and some part of code lies...
I'm developing a Bluetooth mesh lighting controller on a custom board using nRF Connect SDK v2.6.1. I'm trying to add a Sensor Server model to report energy usage, but I'm...
Environment : nRF52833, NCS v3.1.1
Hi. I evaluate PAwR project in my Solution.
PAwR is Fine. But get/set Tx Power is issue.
before add PAwR, My solution used common...
Hello,
I am developing a custom IoT device based on the nRF9151 SiP with a Qorvo QM13345 SP4T antenna switch controlled via RFFE 2.1 interface. All RFFE AT commands fail...
Hi,
I am working on nrf52832 and using SDK 16.
I try to debug the ble_app_buttonless_dfu example, which give error on line 853 in main.c. err_code = ble_dfu_buttonless_async_svci_init...
