Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hello Sir,
We are using NRF24L01+PA+LNA SMA Antenna for transmission purpose using arduino using RH_NRF24.h library.
It is been set to 0dBm transitting power by default...
Hello,
I am working with nRF SDK V 16.0.0. I am using peer manager for my application, can I store my application data too using peer manager? if yes, please help to do...
I try to create coap server project and it should by updateable by DFU. I merge project simple coap server and thread dfu client, and I keep instructions in documentation...
Hello Everyone,
I am Using Nrf51822 module and s130_nrf51_2.0.1_softdevice . my actual function nrf51822 twi interface with stc3115 Gas gauge IC .read the battery voltage...
Hello,
I am implementing ble advertising using below code, i encountered a strange behaviour with this code. If jlink is connected the advertising works just fine. if I...
I have created one characteristic in which i am trying to write multiple bytes at the same time i want to use that for further processing, how to access that whole data which...
Hi,
I just started working with Nordic nRF52840 serial interfaces,can you please tell me which one is best for serial communication among SPI and I2c and why?And can you...
Hi Nordics, I know it has been asked over and over again about doing DFU of slave nrf52 using a central nrf52. devzone.nordicsemi.com/.../ota-dfu-application-firmware-by-ble...
Hi we are trying to program code using the SDK v12.3 library onto a custom NRF51822 board using SES. The custom code contains B luetooth routines, GPIO routines, and TWI routines...
PlatformIO team is pleased to announce the release of Nordic nRF51/52 development platform . This release introduces many new features and performance improvements. The notable...
Hi all,
I am trying to deploy the long range mode with nRF52840. I modified the blinky example under SK 16.0.0 and it just keeps resetting
and the error code is 0x0007...
I feel like a crazy person looking to store large amounts of data onto an external chip that is not a micro-SD (why not micro-SD? It's power-hungry and finicky ). NAND through...
Hi
Please help me sort out one question.
I have a peripheral device that stores an archive with data. At a certain point, the archive is transferred to the central device...
Hello,
We are focussing on the nRF9160 to build a IOT datalogger.
We would like to intergrate an micro SD card.
Now, I mis the 4-bit SPI interface ( SDIO), and I asked...
Greetings,
A very bizarre thing is happening. This is the umpteenth time I'm working on a peripheral driver and the code gets stuck at 'NVIC_EnableIRQ(UARTE0_UART0_IRQn...
