It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
hi there i hope you are doing fine and best of your health. actually i am developing the custom app to communicate with nrf 52840 soc device through bluetooth, which is working...
I am using PCA10056 3.0.2 dk for my application
when search for schematics of this version board I am getting 1.0.x https://docs.nordicsemi.com/bundle/ug_nrf52840_dk/page...
Hello everyone,
I'm looking for some advice on a slightly offbeat topic related to the Nordic SDK.
I'd like to modify the Makefile of one of the SDK examples so that it...
Hi there!
I am trying to make an application that plays an audio sample to a BLE speaker (another nRF5340 running as headset) where the audio sample is in memory. I have...
Hello,
I am writing to inquire about an issue occurring on our custom board.
Ideally, we should print the logs from the device to identify the exact cause, but since that...
Hi everyone!
I have been developing an application for some time and everything has been running smoothly, until recently testing it and finding out some inaccuracies. ...
This library ( https://github.com/NordicSemiconductor/pc-ble-driver-js ) is pretty outdated, and the linked installation instructions are in an archived repository.
I...
I have a chip that I need to read from connected via SPIM. As one might expected, I have a FIFO I need to read from and a data ready interrupt to trigger the read. As an added...
Hi
I'm wondering if I can build a Bluetooth Mesh network for up to 3500 devices. I researched the BLE Mesh standard and theoretically the protocol can create a mesh with...
Hello,
I'm trying to test if my device BLE5 is working properly. I have an nrf52840 pcb and i using the ble_app_blink_pca example. When used the example as is with an BLE4...
Good day! I want to use Fat FS to connect to a micro SD Card on the Xiao BLE board. Is it possible to configure the board without the help of the expansion module? The main...
Hi
I'm trying to add to my Linux board (RPI4 CM) a cellular connectivity and I thought about using nRF9160 SiP because it's a product I've already used and it's low cost...
Hi
Spotify 128 kbps aac stream is about 16 bytes per ms. Ble should support 31 bytes per packet.
So can I stream 16 bytes ms over lte m to nrf 9160 then via uart to...
Good morning!
I hope you will forgive my trivial question but I am a beginner. I don't quite understand the partition structure presented in the "NVS" example. Using the...
Hi,
A veteran of nRF5 SDK but new to NCS.
I tried to run tx_rx_non_blocking example from the latest (2.6.1) NCS SDK, but can't get it to run (nR52840DK)
It seem...
