I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Hi,
My mesh project is occasionally suffering some dropped messages and after probing around I found this on one of the nodes.
I have four nodes and one gateway running...
Hi,
In nrf52840 dongle, I use nrf_crypto_ecdsa_sign function to sign.
Everything is fine in when building, but when testing the real world data, it’ll will show error...
I use 52820 to do ble_usb+esb project, but I have encountered problems when adding USB. I have added USBD_HID_COMPOSIT in the project of \ examples \ peripheral \ usbd_ble_uart...
Dear community
I am developing an autarkic embedded system where I harvest energy from a thermoelectrical generator. It is a simple application, I need to acquire the open...
Hello,
NCS1.8.0 Windows10 X64;
i test v1.8.0\nrf\samples\bluetooth\direct_test_mode, and i want to use nrf21540 model.
i've set CONFIG_NRF21540_FEM=y and do Project...
Hi,
I have been playing around with the nRF9160 DK trying to get it reading a range of sensors, so far with success, however I have found an issue which has stumped me...
We use nRF9160 on our own board. The firmware "Serial lte modem" is installed on the chip with connection to an external MCU. We connect to the broker through the MQTT command...
Hi,
I'm trying to compile Zigbee examples nRF5-SDK-for-Thread-and-Zigbee in Keil but faced some errors.
This is the error I got. This is the exact location of the project...
Hello,
I'm designing a device based on nRF52840 SoC that receives a configuration (set of 50 parameters) from an app which downloads the configuration in JSON format from...
Hi, I tried to run an adc example ( https://github.com/haakonsh/NCS_SAADC_example/tree/master . ) for nrf5340 in another post ( how-to-configure-the-dma-in-adc-and-how-to...
Hej!
Upgrading from SDK16.0.0 to SDK17.1.0, concerning sdk_config.h in my application: I worry that some new options could have been introduced while some old ones might...
Dear support,
I tried to follow the video here for adding service to https://webinars.nordicsemi.com/developing-bluetooth-low-energy-6 ,
Read and notification works fine...
I think I may have found errata. Using the combination in the title I can enable output, verified at the pin using OUTSET. Once the softdevice is enabled the same command...
Hey,
Currently using a nRF9160 DK with an iBasis eSIM (connected to AWS/Azure)
Any good input on using the eSIM as an root of trust? Implementing it as a security layer...
I have been working with the Azure iot hub sample appilcation since version 1.5.0 and use an SD card to store the authentication certificates and other information to connect...
