It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
We've been developing our application using pc-ble-driver which communicates with a PCA10040 devkit with SD API v5.1 connectivity firmware. In this dev environment,...
I'm trying to connect to a few sensors on the Nordic Thingy:52, and it fails with the following message: characteristic is not defined. The connection to the Thingy is established...
Hi,
i use nrf51822 and sdk 11.0 . I am using the ble_app_hrs_c example .This product consists of two devices，One master and one slave.
The master chip is nrf51822...
I am using the nRF52840 (with SDKv17.0.0 + s140_7.0.1) and made a custom FW based on the ble_app_hrs example. My custom HW has a 64MB S25FS512S flash memory chip.
I found...
Hi,
I am currently trying to run the DFU over UART example using my nrf52840 dk. I am using sdk v15.2.0. I followed the following instructions found in the Nordic Infocenter...
I have done a DFU code in our Customized board using NRF52832. My program was running successfully in nrf52 DK but in our customized board it's not working
While uploading...
Hi, I have a BME280 sensor running normally with the nRF9160 on v1.2.0 firmware. When I updated the firmware to 1.3.1, I had to update the code to run I updated the files...
Hi, I have a simple voltage divider circuit and I am measuring analog input from in between the resistors. I am using a custom NRF52832 being powered by a DK. I get quite...
I recently purchased a Thingy91 and have been following the start up guide but have been running into an issue with the thingy91 being recognized over USB. I was able to connect...
Hi Nordic,
I am developing a distance measurement application between the nrf52840 and nrf52833 unit for the long distance mode.
for the nrf52840 as center which running...
HI
I'm using SPI connecting to mutiple max31856(two now) on nrf52DK and SDK15.3
so I control my ss pin to pull low by myself
chip select by changing spi_pin like some...
a data array, length is 2048,use function "sd_ble_gattc_write", a error occurred, length less than 240, no error.
do {。。 err_code = write_configure(m_center_handle,14...
Hi all,
I'm using NRF SDK v17.0.2 and IEEE 802.15.4 stack library. I want to implement sleeping device. I think I should use sys_sleep_request_ms function to make the device...
