hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hello!
Our current project is bare metal and has logging over CLI. I'm in the process of setting up a new project of ours that uses FreeRTOS but reuses a lot of the same...
Hi. I have several questions about mbr.
1). Will mbr finish to write after unexpected power off?
2). Can I copy softdevice + application or only application using sd_mbr_command_copy_sd...
Hello,
We are trying to put togheter a custom mesh communication protocol based on nrf24L01+. Everything was good until we made transmission tests outside, from ground...
Nordic board nRF52 PCA10040, V1.1.1, 2017.1, 682048249.
The pins CTS, RxD, RTS and TxD are currently driven by the MCU. I want to use the SPIS0 in the nRF52832 with the pins...
Is there a Setting in IAR to program nrf52832 without Power cycling
nrf52832 does not start after programming from IAR IDE, using J-Link
But..
For both With J-Link...
I have been experimenting with using some peripherals on the nrf52832 without using the SDK. Primarily of interest to me right now is the low power comparator (LPCOMP).
...
i use nrf52832 .i want to connect device and send advertisment data at the same time. But peripheral mode cannot connct device and send advertisment at the same time. central...
Hi!
I am sorry if I had repeated questions in this forum. I would like to understand few things.
Test scenario
Central - nRF52840
Peripheral - nRF52840
Bluetooth...
I want to add wdt function in ble_app_uart. Please tell me where should I feed the wdt.
in below main loop?
for (;;)
{
power_manage();
nrf_drv_wdt_channel_feed(m_channel_id...
I'm trying to decide the best way to be able to have sub millisecond time keeping, but keep the processor sleeping until it gets a hardware interrupt.
Basically I need...
Hello Nordics Developer
I'm from indonesia, i'm electronics designer, i have develop new products using BLE, first develop i'm using nrf51 series but And my boss ask is there...
I'm trying to conserve space in the advertising packet, and would like to free up the space used by the 128 bit (16 byte) service item list, as this takes a minimum of 18...
Hello all,
I am working on nrf51 series for mesh application so regarding Pre addressing of controller how will get to know the adresses of SOC's in mesh network?
can...
I am using the nRF51822 with the s130 softdevice, and I would like to control three RGB LED modules with three PWMs (R, G, and B). For various conditions, either one, two...
[CONDITION]
1. R1 = 1.5M, R2 = 430K
2. GAIN = 1/2
3. RESOLUTION = 10bits
4. Single End
[ISSUE DESCRIPTION]
1. If voltage is changed by 0.1V step (4.1V -> 4.0V), the...
Hello
I wanted to ask what is the correct way to use NRF_LOG_* functions along with printf (with RETARGET_ENABLED 1 ) and normal UART initialized with standard:
const...
