Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
To whom it concerns:
I'm a little new to Bluetooth SIGs launch studio and need a little guidance on the correct QDID to utilize for my product using Nordic SDKs.
I have...
Hello,
I'm working on a program that receives the temperature over TWI, saves the temperature in a string to flash memory, then adds this string to an NDEF message to be...
Hello,
I have 4Pcs same PCBAs and same firmware, the current values as below:
2.2uA
3.3uA
3.0uA
3.8uA
Condition: Power Supply 3V Battery; Temperature 22...
Shalom!
We have a nRF9160 custom board on which I cannot switch some of the IO lines.
For example we have two leds, P0.9 an P.10 but only P0.9 works. The hardware guy...
Hi there, now I set up a BLE to connect peripheral to central via NUS service. The peripheral is a customize board with nRF52832 and the central is nRF52840 DK board. The...
Hello everyone I hope summer's kind with you (or winter, for the southern hemisphere...)
Here's the deal: my printf and NRF_LOG_INFO output zeros, while my register clearly...
Hi Nordic team,
I am using nRF connect sdk mesh light_switch example. version of sdk is v1.6.1 .
The node is detected in the nRF mesh app in my mobile.
what does group...
I believe I'm following both the Cypress data sheet properly. Yet I'm still having an issue getting the simple QSPI Peripheral example to show data consistency.
Can it...
Hello
I want to operate SSD1331 OLED(96*94) using sdk v17.0.2 and nrf52840 custom board.
The OLED example of sdk v15 was replaced with the codes of sdk17 and tested on...
Hi Nordic experts,
Recently, I consulted the datasheet and tried to find out something about the radio speed when using softdevice, unfortunately, I can't find anything...
We are in the initial stage of development of a product that will be shipped in different countries and different customers.
We would like to use an MFF1 or MFF2 eSIM for...
Hi
When trying to register iBasis sim with correct ICCID and PUK, I get this error message:
Username and pool information are required.
could You help me with...
I have my IMEI but my pin number has 4 digits: 0000, instead of 6 digits(which is required to add the LTE device)? Please Nordic, what should I do? I have this problem for...
I am a beginner in embedded systems.
I know that the minimum resolution of RTC is 1/32768, but what is the effective number of digits for this? For example, I used a counter...
I have not been able to confirm this from documentation. I need to know what the on/off and termination states of the nRF51822 GPIO pins are when the chip is initially powered...
