Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
hello.
I am developing as nrf5-ble-multiple-role-example-master.
And I'm using nrf52832 chip.
When I send a message from the mobile app, I get a message on the SEGGER...
Hi All
I am now working in Channel Selection Algorithm (CSA), Bluetooth Low Energy. Basically, I would like to test both CSA 1 & 2, and also I would like to modify the CSA...
Setup:
SEGGER Embedded Studio for ARM (nordic Edition V4.18 (64 bit)
GCC
Windows 7 Professional
SDK: nRF5_SDK_15.3.0_59ac345
Issue:
In order to use the GPIO...
Eagle pcb and schematic reference designs on github are incorrect.
Reference nRF52840 pcb schematics and layouts are exactly the same for examples 2-6. I believe each is...
Hello,
I am using a nRF52840-DK with an HX711 in SES. I have been utilizing the code provided by Vidar Berg that can be seen here .
I downloaded the zip file, unzipped...
I'm developing the PCB schematic for a system using a nRF52 module that I found that suits my needs SKB369
At the same time I'm implementing a JTAG connector to flash my...
I was wondering: if the last sample of a buffer in the SAADC (using easyDMA and scan mode) is outside the limits, which interrupt would come first, the END or the LIMIT interrupt...
Hi, I am getting a BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST event since I increased the size of MAX MTU to 203 from 23. At first, I received INVALID PARAM error and then found out...
hello.
I am developing as nrf5-ble-multiple-role-example-master.
And I'm using nrf52832 chip.
When I send a message from the mobile app, I get a message on the...
hi,
I have developed light lightness model with the help of generic on/off and generic level model from the mesh SDK. And I have used these models by making changes in the...
Good afternoon,
I am trying to run the example "direct_test_mode" on a custom board based on a nrf52832.
I have succesfully run the example in two development kits ...
Hi,
I´m using nrf52840 with softdevice S132 and I wonder whether the ble_gattc_conn_cfg_t::write_cmd_tx_queue_size is a queue common for all connections or if it a queue...
I am currently testing DFU updates with nRF52. I have run into a situation where the upload of new image is interrupted for some reason. When I try to run the update again...
Target : NRF52832, SD S132 6.1.1. program on Eclipse.
Hello,
Intro :
I migrated to SDK 15.3 for my application and it works.
Then I migrated DFU to SDK15.3 too but...
