hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”,I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hello!
Our current project is bare metal and has logging over CLI. I'm in the process of setting up a new project of ours that uses FreeRTOS but reuses a lot of the same...
Hi,
I'm newbie in the RF Design. For my project nRF52832 chip is being used for BLE and NFC. Have a query regarding the NFC section which is listed below-
Please refer...
Hi all! I want to send data from a beacon (nrf51822) to a Pic microcontroller with the RS232 standard, what function should I use to send data? For example, I can use the...
Hi Nordic Developer Zone,
I also encounter a problem with enabling indications in my Android project. I want to enable Indications so I can gather informations store in...
Is anyone able to access the documentation for the Advertising Module?
Try this:
Go to the InfoCenter at:
infocenter.nordicsemi.com/index.jsp
Select the following...
Has anyone tried to plug an R3 shield to the nrf52 DK?
I was about to try, but it looks like the pins don't line up correctly - but then I have no experience with R3 shields...
Hello everyone,
I'm using the nRF52832, i would like to shutdown the timers, so i can enter the low power mode. In the datasheet tasks_shutdown for the timer modules is...
I have an application which receives commands from a co-processor via UART. Some commands are BLE-related such as, e.g. start-scan, stop-scan, connect, etc.
As the UART...
In nrf_drv_adc.c , there are loads of these ASSERT() macro calls:
ASSERT(mp_state == NRF_DRV_STATE_INITIALIZED);
But there is no variable mp_state. This will fail...
Hi! I have asked a question in this topic ( devzone.nordicsemi.com/.../) and now I can send one packet of 20bytes. What I cannot do is sending two packets at the same time...
I have nRF51 Dongle.
I can set it in BOOTLOADER mode and update firmware like:
developer.mbed.org/.../
I see the dongle in Device Manager/Disk drivers like "MBED microcontroller...
Hi all,
i have a little issue.
If i remove the bond information with app Master control panel, my slave cannot connect again with my phone. [Pairing Reject from Nordic_CTS...
I am moving from S110 and SDK 6 point something to S130 and SDK 10. I have my basic BLE code going but am unable to get the SPI back-in-action. I am using gcc and the s130...
I use NRF51822qfaa,s110 v8.0, now I use master TWI to drive the TWI bus chip.
the TWI bus chip Slave Address is 0x48.please see the below program .
question:
1.The...
this is the main program!
#include <stdbool.h>
#include <stdint.h>
#include "nrf_delay.h"
#include "nrf_gpio.h"
#include "boards.h"
const uint8_t leds_list[LEDS_NUMBER...
Hello,
I migrated from SDK 9 to 11 (S132) and i cannot receive anymore custom advertising (from another nRF52)
I receive another devices advertising events so reception...