I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Hello,
I'm using the PCA100095 NRF5340 development board and developing with the NRF Connect extension for VSCode v2022.3.104 .
When attempting to use the CMSIS intrinsics...
Hello,
In my project i am using nrf52840 with custom board, here i am using BLE UART to send the data from the mobile to device and sending data from another sensor board...
I would like to add Just Works security to our battery service (BAS). However, I could not find such a setting anywhere, so I looked into it and found that in bas.c BT_GATT_SERVICE_DEFINE...
I am troubleshooting a board with no working RF. On looking deeper it appears that the HFCLK is not starting (NRF_CLOCK->EVENTS_HFCLKSTARTED is never set).
This is on a...
Hello,
I am currently working on the NRFX QDEC library with a decoder to be used with a servo motor.
We manage to initialize and enable the QDEC and IRQ and we get...
Hi,
I am facing a problem in adding a power down feature in my application, the details of the application are as follows,
I am using the sensor server example given...
Hey guys,
I have a small concern and decided to ask here, as i was not able to found answer neither in zephyr or nrf sdk docs (not even sure which one apply to my question...
I use the DF example.In Rx.i use both nrf52833 boards as test.i use NCS 1.9.1.
In rx,i use the silab's 16 antenna array for receving antenna array.
because it has 16 antennas...
Topology:
Raspberry Pi A Raspberry Pi B
|(USB connect) |(USB connect)
nRF52840 dongle A )))) Thread (((( nRF52840 dongle B
Software:
nrf52840-dongle: ot-rcp.hex...
In the online power profiler for nRF52832, when I look at the advertising (Tx/Rx) power consumption I see that if I set the Tx payload to 0 bytes the Tx time modeled is 128us...
Hello,
In my project i want two use two UART as off now i am using app_ble_uart example since by default 6,8 is tx and rx pins respectively. so overall application of my...
Hello everyone
I am working on nRF52DK devkit. I want to check the SPI waveform. Actually I want to interface waveshare e-paper display (1.54 inch) For that i used GFX...
On the Thingy 91, the default configuration allocates a lot of flash space to several mcuboot partitions, leaving only 380kb for the app.
I need more space for the app,...
I have a custom application that works well for my nRF52832 device, but my team is moving on to an nRF52840 chip. Long ago, I deleted the directories that were not /pca10040...
