Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hi,
I'm trying to get the maximum possible throughput from a peripheral device, sending notifications to a central. I compare the throughput between 2 PCA10040 boards...
Hi,
I'm using s140 trying to connect up to 8 devices to windows BLE adapter and BluetoothLEDevice object, I have 2 problems,
1- the maximum throughput with different configurations...
Hi All!
I am using Segger Embedded Studio and nRF5_SDK_v15.0.0 .Available kits for testing are nrf52833DK and rak4630(nrf52840).
We want to test nRF52833 support on long...
Both NRF were programmed thru USB NRF connect for Desktop programmer.
Both NRF are running the same soft properly.
To demonstrate the final look and put the dongle in...
Hello,
In my project i am using nrf52810 with my custom board for pushing data to UART so i have used UART example code for this but UART pins are connected 20 (TX), 25...
Hi
I'm working on a Zigbee network, and I want to have a few End Devices (ZED) connect to a Coordinator (ZC). And it's fine, I got that working by using the zigbee_default_signal_handler...
hi
i develop software with the nrf52dk, success with program it with nrf command line tool.
now i want to program the application on the nrf52 dongle but with no success...
I am trying to use SDK version 17.2.0 to develop a package (Boot Loader + SD + Application) for our product based on the PCA10040e board with an nRF52810 SoC.
I soon realized...
There is a serial interface in the nRF SDK that makes it easy to serialize mesh data over serial
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
Hello,
I am want to read Analog value from LDR sensor. I am unable to find ADC Input pin in nrf52840 Dongle datasheet but I got it in nrf52840 chip datasheet (page -576...
Hello Devzone Community,
I have a question set regarding correct, best way or ways to configure nRF9160 GPIOs for high impedance. My hardware is a custom board but shares...
I have the nrfConnect task that builds my project in vscode.
I need to add a script to execute before the nrfConnect task.
I added a task to my tasks.json but the task...
Hi,
Could you please tell me which firmware is flashed onto the thingy91 by default (both for the nrf52840 and for the nrf9160) ? Where can I find the source code for these...
Hello,
We are experiencing a strange issue when quickly turning off/on the NRF52840 on our board. In order to check whether the MCU wakes up correctly, a test fw was set...
