Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Hello,
I am trying to build the Lesson 9 Exercise 1 in the DevAcademy Intermediate course, related to DFU. I get the following error:
error: SERIAL_HAS_DRIVER (defined...
Hi Support Team
The nRF52832 PS mentions that the pin 44 of nRF52832 QFN48 require no connect. What problem if pin 44 of nRF52832 QFN48 is grounded? Many thanks.
Hello, I'm designing a medical product, aiming at IEC 61000-4-2 level 4 ESD protection, and I have a question on the CC lines.
My understanding is that these two lines could...
Hi, I want to set different gap event length for different peripheral on a ble central: 1 link with high throughput and 4 links with low throughput.
The sdk is 17.0.2...
We are seeing our nrf54l15 based device remain in a high power mode after an ADC read using the latest v3.1 SDK (tested on both rc1 and rc2). This did not occur with the v3...
I've been trying to communicate with an external device which supports up to 25 Mhz on its SPI. So, to improve performance, I'm using the SPI3 at 16 Mhz. I have no issue at...
Hi,
I am trying to add an additional storage partition in flash to my project, however, to some reason, pm.yml file is not getting picked up during the build and I am not...
Hi:
I want to use nrf54l05 for the OTA function of BLE. In the example of l9_e5_stol, nrf54L15 OTA can running, but NRF54L05 cannot run.
NCS 3.0.0.
The part I modified...
Hi
I am using nrf70-wifi-ble-image-transfer-demo in the nRF7002 DK.
I change nothing on the code form the sample, after patching I have succesfully build the code and...
After updating to nRF Connect v3.1.0, I am not able to build a project that was started with v3.0.2, nor the matter template sample. When building both my application and...
Hello,
I have been evaluating the DECT NR+ physical layer with nRF9161DK boards with the v3.0.2 DECT Shell sample application. I am wondering if there are going to be any...
Hi Sir,
I have a question about these two configurations in overlay-ppp-cmux-linux.conf, CONFIG_MODEM_BACKEND_UART_ASYNC_RECEIVE_IDLE_TIMEOUT_MS and CONFIG_MODEM_BACKEND_UART_SLM_TRANSMIT_TIMEOUT_MS...
Hi,
I recently started working with the nRF9151 DK and was able to run the initial demo programs without any issues. To continue testing, I picked up a Thingy:91 X, but...
