hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hello everyone,
for a low-power application, I need to evaluate the total power consumption of the nRF52840 Dev Kit. To verify my measurements, I set one of the GPIOs to...
Hi all together,
nrf52810 SD112 SDK 15.3.0
I have a problem writing to flash with the nrf_fstorage module. I try to write an array of 32 Bytes into flash, triggered by...
We currently want to use the USB Dongle nRF52840 to monitor a communication between two Bluetooth devicesand we are new to this field. First we installed the nRF Connect for...
I am trying to build the AES crypto example in the SDK <install_dir>\nrf5sdk\v16\nRF5SDK160098a08e2\examples\crypto\nrf_crypto\aes\aes_all_cli (nrf_crypto_aes.eww).
Compilation...
Hello,
I am using nRF5340DK board and I am trying to enable high-speed SPI pins in nrf5340dk_nrf5340_cpuapp.dts
&spi4 { compatible = "nordic,nrf-spim"; status = "okay...
Hi Team,
We are trying to connect our product (thingy91 reference) to the Link Monitor application to check LTE connectivity and antenna performance.
Loaded nRF52840...
Hi
there are some question regarding this in the forum but I didn't find any clear approach on changing the MAC address.
I'm on SD132 with SDK17 and want to change the...
I just got started with the nrf9160 DK and I tested it with the Asset Tracker application (following the getting started video). At first everything was working fine and I...
If I am creating an application using the Zigbee stack running with nRF Connect SDK and Zephyr, what hardware is not available to me because it is already consumed by the...
I have both a NRF9160DK which I can program and, Zephyr, blinky Serial modem etc, all work on the DK and I also have a nrf91 Thingy.
The Thingy won't respond to programming...
Hi Nordic
One of My customer employs nRF52832-QFAA in their product. They use SDK 17.0.2 and SES to develop their product。
They found the flash is now enough(they use...
I have a NRF52840. To save some energy I wanted to disable the soft device so that there's no bluetooth activity at all. However instead of an average consumption of about...
I am developing BLE Mesh product with `nRF connect SDK`.
I understand most of sample project has a function of proxy node. But I don't know how to connect a provisioned...
