I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
Hello,
I'm trying to develop a wearable stacking form-factor where number of boards can be assembled in a deck: MCU, sensors, actuators, power supplies, etc. Size of the...
Hi ,
I want to compile mesh examples .I tried it using segger ide Alternatively,I wish to compile it in cmake too. Can you please tell me the procedure to compile code using...
Hi,
I was able the configure the sample to connect to AWS but I cannot figure out where the cloud_send function is sending the data. Is there any documentation on where...
Hi all,
I am using a nRF52840-DK as SPI slave with a MSP430 as host SPI master for a nRF8001 replacement application.
As I am absolutely not familiar with high level functions...
I am trying to communicate with a SH1106 OLED display using TWI and the popular u8g2 display controller library.
I've verified that the display works without problems on...
I am currently development an app based on the example from the experimental folder using a NRF DK52 as a relay between a central and multiple peripherals.
The app should...
Hello,
Happy New Year.
I'm not able to find nRF52840-QIAA-T or any replacement of this SoC available in the North American market.
I need atleast 5 SoC of the...
Setup: nrf52840 (without internal dc/dc), VDD = 3.3V
Assuming the VDD rail ramps up slowly, the nrf52 will start booting at it's power-on reset threshold of 1.75V (POR)...
Dear BLE Experts, I've followed this tutorial to create a custom GATT service and characteristic. The tutorial seems to be based on the BLE SDK , not the MESH sdk, hence the...
Hello,
Our company is kicking off a project (while we are at the very beginning stage) where multiple nodes (up to 1K) should be connected within a mutual network. I wanted...
We are looking to increase battery life for a product that uses the nRF52832. I'm wondering if it's possible to provide 1.3V directly to the DEC4 pin rather than use the internal...
Hi, I'm referring to this post over 3 years ago: Nordic DevZone (nordicsemi.com)
I'm using Android 8.0, and I'm using SDK 12.3.0 for firmware. I'm trying to create bond...
Hi,
I noticed that when I initiate a chip-erase on the flash-chip and reset the MCU, I'm getting NRFX_ERROR_TIMEOUT's on my nrfx_qspi_init().
I found this ticket: https...
i am using nrf52840 DK with softdevice (s140_nrf52840_5.0.0-1.alpha_softdevice) and applying this throughput example ATT_MTU Throughput Example . and notice that when I use...
