hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
I have the following setup:
nRF51 dongle
connectivity_115k2_with_s130_1.0.0.hex firmware
Windows 7 PC
nrf51-ble-driver_win_0.5.0
My app is written in...
Hi,
I see that you provide Master emulator API for windows (dll) that works with firmware for Master control panel application. Master control panel firmware, as the name...
Hello,
I try to set up an external signal for the LFCLK on a nrf52832. From this question :
I know the nrf52832 can do this (signal on XL1 pin, XL2 grounded).
...
Hello,
I am working on development to concurrent multiprotocol: BLE+2.4G proprietary. I am using timeslot feature in S132.
Because in my own 2.4g proprietary protocol, the...
I want to use feature reports in my HID project, but as far as I see this functionality is not fully included in ble_hids.c (SDK 11). I already managed to properly receive...
Hi,
I want to advertise in variable intervals and mostly only one advertisement at a time. I planned to do it like this:
1- start advertising with any interval (e.g...
Hello,
I followed the example for doing 128 bit UUID advertising using ble_app_uart example. The problem is, this seems to work if I run it when the radio and controller...
Hi,
I have my custom nRF51822 board based on Raytac MDBT40-P module. I am trying to program it with nRF51-DK(PCA10028). I could program it with mbed interface once or twice...
Hi,
I want to implement Advertising with the Timeslot API. I only need non-connectable advertisements but I want to be able to control the transmit power.
Which example...
Hello all,
I would like to understand advertisement packet more.
if I add the following to my packet my firmware causes nrf51822 to crash.
advdata.include_appearance...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
I'm using the BMD-200-EVAL S board (using Segger JLink). I've defined SCL and SDA as:
#define ARDUINO_SCL_PIN 5
#define ARDUINO_SDA_PIN 8
When debugging into the...
As title, where can I find the syntax for this editor?
If it does not exist,
Q1. How can I put sample source code block?
Q2. How can I put new line only? (without...
Hi,
What's the maximum current for nRF52832 when only CPU is running from RAM at 64MHz (DCDC 3V condition)?
From Product specification v1.0 page 18, does the value "3...
