I wanna implement this code for the app inventor, but there was several problem here. I can't use array or index for developing my trapezoidal method.. like this..
code...
Hello,
We are looking for a developer a single task project. We need to provide all of our developers with the same development environment, so we are looking for someone...
I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi Nordic Team
I encounterd the following behaviour:
Segmented message took 8s for acknoledge state.
I did the following:
Setup: 2 Devices NRF52840DK, provisioned...
Hi,
I'm using nRFConnect 2.6.1 SDK on a nRF52833 with the speed build optimization.
I got two peripherals on the same SPI which is SPIM3. It is configured at 32MHz and...
Hello everyone,
I'm working on a Bluetooth device using the Zephyr framework. I need to maintain a current connection while also continuing to advertise. If another device...
I am using nrf5 sdk 17.1.0, segger embedded studio v6.40 and nrf52832-dk, when running the spi example, i do able to see the log only after the build, and when i reset the...
Hi,
I'm starting some development with NCS on the thread CLI sample and I wanted to adapt the code to work on a custom module. The goal is to be able to log some data through...
Hi,
I have been running thingy91 to learn more about nRF_Connect SDK and the assets tracker project.
I did all the beginner-level steps, hardware setup, nRF cloud setup...
Dear Nordic developer community,
I am in the process of developing a communication with the PC via the USB CDC ACM interface of the nRF52840 chip. The information received...
Hello Community! I am working on a small project on nrf52832_mdk beacon Where my main goal is to optimize the current consumption. I removed all the unused peripheral and...
Developing a device based on the nrf5340/nrf7002 pair, with a user interface.
I decided to use the Nordic 'buttons' and 'click-buttons' modules from the CAF framework for...
Hi All,
We are currently using this nRF-5340DK to understand the individual driver functionalities before we start our project with our kit .While doing so we encountered...
I am trying to get a pancake motor working with a nRF5340 using Zephyr in VSC. I have an intermediary board.
I keep getting this error:
I have these settings in the...
HI there, In the Serial LTE Modem documentation for the nRF9160 DK, it is mentioned that the GPIO voltage level should be 3V using SW9 when using an external MCU & UART2....
Hi, I am using the Nordic NRF52832 with SDK 16.
My device is configured to advertise continuously for a specific duration.
However, when tested using the nRF Connect app...
I am attempting to get the BMI270 sample working on an nRF5340DK, using nRF Connect SDK v1.6.0, but all attempts at device_get_binding("BMI270"), device_get_binding(DT_LABEL...
We are trying to interface Texas Instruments TMP144 using the UART in nrf52DK. We attach the sensor board to UART pins in nrf52DK put it seems that the transmitted data is...
