I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
As stated, LE Audio is based on LC3 codec and isochronous channel. They are both software stuff, no hardware related, like PHY.(Is this right？)
So for BT5.0/BT5.1...
We'd like to evaluate the nRF9160 for our device as a replacement microcontroller + LTE-M modem.
Working with the DK should be fine for evaluation purposes, but in the end...
I do the install by step , https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_installing.html
the toolchain install failed when on step 5;
log as belowed...
Hi All,
I am currently implementing Write communication, referring to ble_app_blinky in example.
When the phone gives the command, the program will run this function,...
I'm attempting to control a PA attached to an nRF52840 in a way similar to Case ID: 212504
But I'm also using Zephyr...
Are there equivalent calls available via the Zephyr...
Hello，
We are using NCS v1.9.0 and nRF51820 SoC in our project.
Here is a question about using the COMP function.After I configure and initialize COMP，it returns NRFX_SUCCESS...
this is ADC config
This is the electronic schematic
Q13open，CURR N1和CURR P1 get parameter from temperature sensor 。OUT1 is temperature sensor ，it was 0.5Ω...
Hi,
i am working on nrf52 dongle. i want to use ble_app_uart example with it. how i can receive data on uart with usb. i can send data on ble but not receiving on uart....
I want to creat a hci vendor-specific command of zephyr using nRF connect SDK, based on hci_pwr_ctrl bluetooth sample.
At first, I think just using follow steps in hci_vs...
Hi,
Recently I have heard that there are license restrictions on using DKs for production programming. Is this only for production programming? Can I still use the DK to...
Hello, im trying to implement the UARTE Driver for simultaneous Use of Bluetooth and asynchrounos Uart TX/RX on a nRF52840 and nrf9160. The Problem is that neither RX or TX...
Hi
i want use a nRF52840Dongle as a Zigbee end device, when power up, i get following message:
I: nRF5 802154 radio initialized ***** delaying boot 5000ms (per build configuration...
Hi, I have just started evaluating nRF52840 using the dongle and Development Kit. I have successfully tested the Openthread network using CLI project. Now I want to try out...
